MFI2568AES Maytag Refrigerator - Instructions

Lifted glass and replaced shelf bar - SIMPLE SIMPLE SIMPLE

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.

Simply remove the two fruit/vegie drawer and the glass pantry top. Lift off the front support for the glass. Using a nut driver, remove the 2 screws that hold the pantry cap onto the side of the fridge then remove the end cap and temperature control. Remove the two screws that hold the drawer slide to the end cap and transfer to the new end cap. Now transfer the temperature control slides from the old end cap to the new. Some twisting and bending of the plastic slides will be necessary so be carefull not to push too far and break them. Reverse the removal until everything's back together.

Remove screws holding pantry end cap to refrigerator and sliding bracket from pantry end cap, which holds deli draw in place. Remove plastic hardware from old to new, then replace screws in reverse order of there removal.

very easy, my reading the reviews i knew exactly how to do it, and it really didnt take 15 minutes. hardest was taking all the shelves out, but i had that all done ahead of time. as the part came very fast. perfect job and i did it not my husband. great company. i will diffently order from you again carol in beverly hills fl

remove old replace with new part easy as that no brainer

After removing the glass shelf I simply removed the broken center rail and popped in the new one. It took only a couple of minutes from start to finish.

Ordered parts. They were here in 1 day. Followed directions on internet. Crisper slider took 10 seconds to replace after removing crispers and cover glass. The pantry end cap was replaced exactly as shown on the web site and took less than 5 minutes. Be careful putting cover back on the end cap because you do not want to snap the nib again.

Pins holding the door in place are part of the plastic end cap on either side of pantry drawer. Very easy to replace. Need only to remove two bolts holding the broken end cap in place, remove the drawer slide from that piece by removing two more bolts, reinstalling the drawer slide on the replacement end cap, and reinstalling the new end cap. Part was surprisingly cheap and arrived much sooner than indicated.

I actually hired a handyman who easily performed the repair

Removed crisper drawers, removed glass shelf and deli drawer and cover. Remove screws holding the sliding attachment and pantry end. After taking the old pantry end off I noticed that there was a plastic insert that went from the front to the rear, made a 90 degree turn and went to the rear area of the unit and was used to control the temp in the deli drawer. Took a little while to figure out how it worked and finally put it all together and reversed all of the steps taken to replace everything. Once I figured out the temp control slide it was easy to get it back together.

It took longer to open the package than to install the new part. No tools required.

Looked at questions, picked one that applied, ordered suggested part, fix was super easy after watching video, Frig in running, part fixed it. Very excited, Thankyou.

Unscrewed the old filter and screwed in the new one

One mnorning the temp on the frig was in the 50's and the freezer was cold. Tried to get someone to come out and repair with no luck. We purchased a new frig. Then I decided to see if I could repair the old one to use. I wish I had discovered partselect before I bought the new one. First I thought from the web site that it was a overload/relay problem so I ordered it and changed it out and it was very easy. Then that did not correct the problem so I checked further and discovered that it could be the defrost heat element and thermostat. On partselect web site I saw where if your coil is covered in ice that this could be the reason. I ordered them and watched the video of how to change them out. The video is a little misleading because chances are you will not have the room around the coil that it shows on the video and also the element and thermostat will not come as one unit as shown on the video. It is still easy to cut the wires ont he thermostat and install it. The heat element is a little tricky to get out and back in and the clips that holds yours might be a little different and more difficult to do than the video but you can do it. All in all I spent about 160. 00 And the frig is working like new.