Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door switch was broken
I typed in on my brouser Repair Kitchen Aid Dryer door switch. And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away from the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
When using the dryer the cycle would stop and display E1 as the reason
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very happy customers.
Dryer made a terrible screeching noise when tumbling.
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!
Unplugged washer,removed the two screws by the lint trap,moved the top foward lifted the top (it'shinged in the back )the switch is right inside the door top right hand corner removed the two screws that hold the switch in place used a flatblade screwdriver to seperate the connections pulled off the old installed the new switch put every thing back together worked as though it wes never broken
The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.