Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The problem was the dryer wouldn't heat up (gas). Would run but just not heat up.
So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.
I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.
Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.
The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)
Can't beat parts select!
Parts select + a little know how, saved me about $400.
this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!
The dryer wouldn't turn on after pushing the start button
I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!
Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help
After receiving the part I pulled the dryer out for easy access. Used only a nut driver to remove back cover and the part to replace was easily identified. Then it took a little while to remove all the dust and other particles that had built up over the years. The actual replacement of the part only took a couple of minutes. Reattached the back cover and put back in place. Turned on dryer and I now had heat. Easy fix.
My wife and I thought our dryer was done and we were looking at a large replacement costs. We started googling and found this site and watched the video. We are were 99% sure it was the thermal fuse. We received within 2 days and thought we would be in there for over an hour. Turned it was less than 10 minutes, we watched the video clip on how to install on our laptop as we did it.
We will always be buying parts from this site and have told a ton of friends/family to check this site out.
Longest time needed was to determine what cause was. After that ordering part from PartSelect was very easy and saved me money. Part arrived before time given, part was correct and installed without problems.
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
There was no heat but the dryer would operate properly in all other functions. I checked the ignitor (gas dryer) with a meter and it was okay. I traced the circut back and ended up at the thermal fuse and it was "open" I jumped it out and the dryer started to work. I knew the problem was the thermal fuse but more importantly why did it blow. Further investigation showed excessive lint in the duct. Needed to take the exhaust system apart and clean out the lint. also replaced the flexible dryer (too difficult to clean) and to make sure that I didn't over work the high/low thermostat and would be doing this repair again in the near future I replaced that also. Be careful and do not jump out the fuse and use the dryer as this will cause a fire. I did it to prove the problem only... Dryer works well again and we will probably get another 5 years out of it!
It took me 5 minutes to find PartSelect's site, read the comments about the most common problems and identify the solution. The exploded views were a great assist, as it wasn't obvious where the thermal fuse is located or which access panel to remove.
It took less than 5 minutes to remove the rear panel and install a temporary jumper to verify the blown fuse was the only issue. With the new fuse in hand, replair took another 5 minutes.
A word of caution to anyone replacing is fuse - I found that the exhaust vent pipe to the wall was full of lint and nearly blocked. This is a potential fire hazard. While enough air was passing through the flapper vent to make it look like it was OK, the exhaust resistance is what caused the overheating and made the fuse blow.
I spent more time cleaning out the vent pipe than replacing the fuse, for a total of 25 minutes. I strongly urge all dryer owners to physically inspect the exhaust duct annually.
PS Drying time has decreased by 30-40% since the repair.
The major issue was getting the dryer out and cleaning it all up. That's what took the time but it was worth it to clean out the lint in the ducts, etc.. Putting the thermal fuse was a snap thanks to the great feedback received when I got this web site and read the previous responses.
I opened the front lower cover to get the schematics. Looked for the most probable part that was bad. Then traced wiring from the gas solenoid to find the thermal fuse. I opened the back. Took the two wires off the thermal fuse and put my Ohm meter from terminal to terminal. As I got no reading, I ordered a new fuse. It took about 5 minutes to replace and button the dryer back up. This is the second time I have had to replace this fuse.
