MDE17MNAYW1 Maytag Dryer - Instructions

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

Installed new door switch, so, so simple. Unplug dryer, remove lint screen, undo 2 scews located at base of lint screen opening. Use flat head screw driver to pry up dryer top, once open, rest the top against the wall. Now you will see the door switch in the right hand corner at front of the dryer.Open the dryer door , remove 2 screws holding the broken switch, disconnect wire from dryer, click in the new switch, put everything back together, plug in the dryer and go! Super quick and easy, wish I had just done this months ago!!!!

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

Once I had determined that the door switch was broken (the black actuating arm was broken) I ordered a replacement. The procedure to replace it is the reverse of removal of the broken part: unplug the appliance to begin. There are 2 screws that hold the filter frame to the top of the dryer; these are removed and set aside for reuse. The top of the dryer can now be pulled up to gain access to the door switch. Make sure you leave enough space behind the dryer to prop the top up without letting it go backwards. Disconnect the wiring harness plug for the door switch and the unscrew the switch. There are 2 screws accessed from the upper right corner of the open door. Replace the switch, guiding the 2 screws into the mounting holes of the part, remembering to not over torque the screws, connect the wiring harness, close the lid, replace the 2 filter housing screws, plug the dryer back in to the electrical outlet and you should be good to go.

I removed the part located on the dryer at the top of the door area. I installed the new part with the two screws I removed and BAZINGA...it all worked again. Very pleased!

This problem occurred Thursday afternoon; after I took out a load of dry clothes, it wouldn't restart. I realized that the switch was busted, it used to click but it was just hanging. Watched the video and ordered it right away. It arrived Saturday morning via Fedex and I installed it in about 5 minutes. It probably took longer to watch the video. 23 bucks and the dryer's running perfectly. I've replaced several parts this way on my appliances, always feels good to do it yourself. Good as new.

Took old one out and put new one in. Popped the top off and took out two screws. That was it.

Removed the old screen and simply put in the new one

With the instructional video the repair was very easy.

Remove old filter
Vacuum out
Install new filter

replaced dryer lint screen with new.

Took back panel off, and it was really easy putting the new idler pulley in.

Remove old filter, throw it away, replace with new filter.