Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken latch on door
Spent 1 hr following video. Difficulty was taking part apart & attaching new latch handle to latch assembly. Called PS tel support & spoke w/Breanna who was patient & tried her best to coach me. Sent photos to her via email to show what part looked like. Her boss discovered latch was attached upside down. Tried very hard to reattach in the correct direction. To no avail. Was advised to call Whirlpool tech. Instead, contacted handyman to complete repair.
I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.
Remove all interior door panel screws with a torx head screwdriver (drill). Pull the interior panel up from the door far enough to access the switch assembly. Pull it out and remove the 2 electrical connectors from the old switch (using a small screw driver as a pry bar if needed). Remove the old switch and handle (that may be broken off and still in the door). Push the electrical connectors onto the new switch assembly, making sure the handle is down toward the opening and the connectors are on the same side as they came off of the old switch. Align the mounting screw holes of the switch with the threaded holes on either side of the switch. Push the interior panel back together and align the two holes with the switch holes (those 2 screws go through the door panel and the switch assembly). Replace the remaining interior panel screws. Done!
Who ever assembled the parts for shipment, put the latch on backwards and it was extremely hard to take the latch off of the main part. Now matter how hard I tried, I was unable to re-attach the latch until I used a file on the plastic insert to file off the inside edges until they fit. It does work now, but it could have been made much easier if they had simply positioned the latch in the correct position in the first place.
Door handle was broken and would not release consistently
I removed the inner panel from the door. The handle and latch assembly was accessed right under the top of the inside cover. The wires were removed from the two switches. The new switches were connected on the new latch assembly. The assembly was placed on the outter door panel and the inner door cover was screwed back in place. Quick easy repair! Works likes new!
I noticed that the dishes on the top rack were not getting clean. While the dishwasher was running, I opened the door to see if the arms were moving/spraying and they were not. I cleaned the filter and checked the impeller and both were clean and not damaged. After looking how the top rack slides into the "flapper" I took it off to inspect it. It was missing the rubber to make the seal with the tube from the top rack. After replacing this part, the dishwasher is cleaning like new. Here is the part PS2340934 Docking Station with Flappers
spring on one side of door broke, door became heavy and wouldn't stay up
Unscrewed dishwasher from counter and pulled it out from under the counter a few inches. Looked at the side of the dishwasher with the remaining good spring and saw how it was attached: One end was hooked to a little tether strung around a pulley, the other to one of a few steel slots. Copied that side for the new spring and works fine now.
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.
The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.
The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle. All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends. Thanks, Harold L.
By reading online about some similar problems, I discovered that the accumulator did, in fact, have some holes worn through the screen and was leaking sediment back into the rinse water. After waiting for 2-3 months because the apart was on back-order at the factory, it took me less that 1 hour to remember how the unit went together (reviewed the parts diagram online) and connect everything up. On the first rinse, the dishes were really clean - well worth the wait. Doing dished by hand reminded me of the old days....
Very easy to replace the roller. First I removed the stop on the top slide. Then I unsnapped the old roller. The new roller just snapped right in place. Then I put the drawer slide back on.... Took less than 5 minutes.