MDB8951BWQ10 Maytag Dishwasher - Instructions

There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks to clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked.
I guess I was lucky because on the other side of handle similar type of part thats maytag for you.

Simple. Unscrew the old one, replace with the new one.
The best part- Online said it would take 5-7 days to recieve thru the mail. It arrived the very next day!!!!

took screws our of side trim and top trim, decreased height on leveler legs and pulled dishwasher from the cabinet, replaced cables and springs from both sides on the door, lubed door hinges cleaned everything under dishwasher re-inserted and re-installed trim screws. took around an hour with clean up.

We took out old racks and installed the new ones. On another note, after ordering (or trying to order) parts from appliances older than 10 years old several times, I think manufacturers stop making parts after 10 years. So if you're thinking of replacing a part on an older appliance, try to look for it sooner than later.

Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

I removed the old rack adjuster by unscrewing four screws. I put the new rack adjuster in place, carefully fitted the adjustment parts together, then replaced the four screws. The best part of the repair was that Parts Select had originally indicated that my part would be on back order for a few weeks, but I actually received the part within just a few days. What a nice surprise - thanks!

Basically took out of box and put in dishwasher.

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Initially ordered the rack adjuster assembly, not realizing that I would also need the adjuster lever and adjuster cover, too. This piece is NOT what originally came with our unit. The line drawing for part 17 shows what our unit looks like. That part has apparently been discontinued and we were guided by Maytag to order this substitution, which is actually a Whirlpool part. Thought someone else might want to know this if they happen to have the same series of Maytag DW as we do. It fits well onto the rack, however, the location of the wheels on the unit are different than the original which means that the middle rack now slides out of the dishwasher about 3" less than it used to, which is kind of a bummer. All that said, the repair was a piece of cake and the hubs on the wheels are now metal instead of the original plastic. . .I expect this part to last a good long while!

I unscrewed the old rack adjuster assembly and screwed the new one on (this was after I took the rack out of the diswasher) -- I actually saved one of the old intact plastic wheels for future repairs.

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.