Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
knob fell off, and burnt in the wash cycle.
Simple. Unscrew the old one, replace with the new one. The best part- Online said it would take 5-7 days to recieve thru the mail. It arrived the very next day!!!!
Plastic handle latch was cracked and door was very difficult to open/close
First turned off power to dishwasher. Then, I removed all the screws on the dishwasher door. Removed old plastic door latch from wire assembly piece. Pressed on latches for square small wire boxes connected to wire assembly piece to be able to handle wire assembly plastic piece without attachment to dishwasher. Tried to snap door handle to wire assembly plastic piece, but didn't seem to fit - was too tight. Checked for discussion online and found that it required heavy pressure to snap in place. Used pliers to clamp down on outer plastic on wire assembly piece to squeeze fit door latch plastic hooks in place. This was difficult, but with heavy pressure finally managed to snap in outer hooks. Then with difficulty snapped in inner hooks. Was afraid of breaking new plastic piece, but all worked out well. Door has never opened and closed so well!!
All i had to do was ....first unplug the dishwasher,then remove 10 of the Torx head screws on the inside of the door.(from the top down) With that done i could open the cover without taking it off. then unplug the switches,and replace the new handle. screw the cover back in place. done! piece a cake! MD PS (don't forget to plug it back in)
after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked. I guess I was lucky because on the other side of handle similar type of part thats maytag for you.
door spring broken door would not stay up very heavy to lift
took screws our of side trim and top trim, decreased height on leveler legs and pulled dishwasher from the cabinet, replaced cables and springs from both sides on the door, lubed door hinges cleaned everything under dishwasher re-inserted and re-installed trim screws. took around an hour with clean up.
We followed the instructions in the video online to replace the latch assembly. Removing the electric wires from the old latch assembly was difficult; I read that others had trouble with that too. Two of us worked together. I inserted a screwdriver between the plastic box shaped thing holding the wires and the old latch assembly --- between the two metal pieces that extended from the latch into the plastic box shaped thing. I pushed the screwdriver thru until I could hold both ends. I held tightly while my partner pulled the latch assembly off of the wires. Repeat for the wires on the other side. Pretty easy. So happy to have fixed it ourselves.
First, we removed all of the screws around the perimeter of the interior door panel and lifted it up. (we didn't take it completely off because that would have required disconnecting wires so we just held it up out of the way.)
Second, the plastic on the latch assembly was broken so that part came out fairly easily. The hard part was disconnecting the metal prongs that plug it in to the door control wires. We tried everything--prying, pulling--and finally got all three of us in there. One pulled on the latch end of the prongs, the other pulled on the door wiring end of the prongs, and I squeezed the prongs in-between with needle nose pliers. This broke the prongs on the latch side, which was fine since we were replacing the entire latch (the directions in the service manual we downloaded didn't give any indication that disconnecting the prongs would be difficult--I feel like there must be a trick to it, but breaking the prongs worked fine too!)
Third, we plugged in the prongs of the new latch--went in easily!--and popped the new latch into place in the door. It wasn't held securely, probably because of the broken plastic, but we replaced the inner door and screwed it in place, and when we shut the door it worked.
I removed eight screws and installed the new parts. The replacement factory parts are better then the originals and the latch handle should not break again. Had I called for service it would have cost $149 (not incuding parts) just for them to show up to look at it and tell me that they need to order these same parts. Plus, I would have had to wait an addtional two weeks for them to order the parts and come back to do the repair since most service companies do not carry parts with them. Their parts are marked up and would have cost 30% more for the same factory parts I order from you. The parts including shipping were $36.30 and I had the repair completed in three days, including standard shipping time. Quite a savings! and very easy to complete the repair.
Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.
The spinning wash arm above the glass rack broke off
The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...
I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.
When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.
A for maytag for making it easy to fix A+ for PartSelect for making it so darn easy
Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts. Dishes finally coming out clean!
portions of the upper and lower rack had deteriorated and were rusty
We took out old racks and installed the new ones. On another note, after ordering (or trying to order) parts from appliances older than 10 years old several times, I think manufacturers stop making parts after 10 years. So if you're thinking of replacing a part on an older appliance, try to look for it sooner than later.
Removed filter cover and filter and found the plastic chopper sleeve was stripped out. Followed instructions that came with the seal kit to replace it.
Disconnect the power,open panel and remove screws with the exception of the two bottom ones. This allows the panel cover to be opened far enough to pull latch assembly clear. Remove electrical contacts (2) and put defective unit aside. Connect new latch unit to both wire saddles,line up unit with proper holes and install two screws. Once fixed in place,install all other screws and switch power back on.Do a short test run to check for any leaks
1 - Disconnect the electrical power 2 - Open the dishwasher door 3 - Use Allan wrench to remove the screws from the inside door panel 4 - Separate the inside pane from the door 5 - Remove the latch assembly 6 - Use a screw driver or pliers to remove the electrical connectors from the broken latch assembly 7 - Connect the electrical connectors to the replacement latch assembly 8 - Place the replacement latch assemble in the door 9 - Replace the inside door panel 10 - Replace the screws to secure the inside door panel 11 – Reconnect the electrical power