Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MAV7600AWW > Instructions

MAV7600AWW Maytag Washer - Instructions

All installation instructions for MAV7600AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAV7600AWW
241-255 of 417
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Blades broke from agitator

  • Customer: John W from Ashland, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Parts where in, in a timely manner. I remover the fabric softener cup on top of agitator. User a 1/2 inch socket and a 3/8 ratchet with an 8 inch extension to remove the center nut. Popped the agitator out. Installed in reverse order, only tightening the nut slightly. The install went just like the video. Thanks much.

The washer was not expelling water

  • Customer: Dickie from Pueblo, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am pretty much a novice at appliance repair but am curious enough to investigate and try to save some money. I found what appeared to be the worn part but even being unsure I ordered it. It turned out it was the right part and after installing it I reassembled the washer with no spare parts left over. During a test run it was discovered that the washer drain was partially plugged. I left the drain to the professional and after that all was fine. If it ain't one thing it's three.

Washer was making a clicking sound during wash and spin cycles.

  • Customer: Theodore from Jacksonville, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug the power cord and hoses. Pull washer away from the wall, tilt it backwards, reach under the washer and remove the belt.The motor has a spring loaded pulley which allows slack to roll the belt off. Turn the washer to the back is faceing you. There is a small panel with four screws in the lower left corner, take them out and remove the panel. Then you will see the drain pump. Remove the two hoses, the three screws holding the pump assembly. Remove the bad pump, and install a new one. Assemble every thing in reverse order, and sart washing.

Severe Vibration And Movement

  • Customer: kenneth from crystal lake, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
I followed your advice for the part and watched a you tube video and it fixed the problem completely. . . . I am very happy and will relay this to all my friends. Take the time to check thoroughly what you are doing since the first video didnt tell me that there was a high pressure spring under the ring that held the snubber but I discovered this by watching the video and it all worked very well. Thank you-you saved me $700. 00.

Water leak from the bottom of the drain pump

  • Customer: Keith from Pickford, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
It was very easy. Through the access panel in the back, remove both hoses, take out three screws with 3/8ths socket, remove pump being mindful of the belt and pulley, re-set the pump with belt in place, put the three screws back in, re-connect the hoses, and done ! 10-15 minute job at the most. There will be some residual water in the pump when removed.

Machine was making really loud noises

  • Customer: Benjamin from Wylie, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Tilted the machine to remove the belt. The removed the rear access panel, disconnected the hoses and using the socket set with an extension removed the existing water pump. Put the new one in, reconnected the hoses and put the access panel back on. Much easier than I thought it would be! Now the machine is as quiet as the day we bought it!

BAd Noise & finally pump Locked up

  • Customer: Fred from Marissa, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought the noise was the thrust bearing. Replaced it but didn't fix. Washer worked but hstill had terrible noise. Went shopping for new washer - then pump locked up. I siphoned out the water (good idea) and folled ditections I found on this site. 1. pryed up top with screwdriver. Raised lid. 2. Removed the 2 front panel screws with a nutdriver. 3.Removed hose clamps from pump with pliers. 4. Removed 3 screws holding pump. 5.Replaced pump in reverse order. 6. Crossed fingers - it works fine - saved $800.00

water running from under the washer

  • Customer: wanda from cookeville, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
new water pump

Pulley coming off of pump.

  • Customer: WILLIAM from FORNEY, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old pump, disconnected hoses and drained water. Put hoses on new pump and reinstalled.

loud noise on rinse & spin cycle

  • Customer: Betsy from Van Buren Point, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back inspection cover which was two screws,the pump with pully was right there. Removed the belt and three screws from the pully and pulled it out. Put new pully in tightened the three screws put the belt back on and the inspection cover plugged the machine back in turned it on and it ran perfect.

Burning Rubber and Metal on Metal Sound

  • Customer: Russ from Fenton, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Rubber belt was getting shredded. I replaced the motor and motor pulley (because the are one piece), but the metal on metal sound was still there. I then did some research and found out the water pump pulley could be the issue. I took it out and felt the grinding. Decided to try and tighten the screws on it, but the sounds was still there. Ordered the water pump and it was so simple to replace. (talking with my Maytag store this would have cost me over $400 to fix. With PartsSelect.com the total cost was $225.

no contact with lid switch

  • Customer: Sue from Vienna, WV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed old part using phillips screwdriver and replace with new assembly parts.

machine would walk across floor & shake vilently

  • Customer: William from Hayesville, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Repair went as described in instructions supplied and YouTube Video "snubber ring". I could not have removed tub springs without putting 72 quarters in springs before removing as seen in another repair video which made removal and reinstallation doable. I still don't understand how this inexpensive part can cause such a problem.

The water pump bearings wore out and the pulley broke off

  • Customer: Barton from Barto, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the new part on a Sunday and it arrived at my house on Tuesday. Removed the back cover plate,(only two screws) removed the two hose clamps and hoses. Removed the three screws holding the old pump to the base and took out the bad pump. Put the new pump in place, (a perfect fit) and put everything back together. Even the belt went back on with ease. The washer was back in place and working perfectly in about 15 minutes.

Washer wouldn't spin.

  • Customer: Charles from Sherrodsville, OH
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After reading several online posts about this problem on appliance forums and following the suggestions about how to determine what was needed (whether the inner tub turned freely (by hand) in spin mode or not. It didn't which apparently indicates the likely need for a new thrust bearing. I purchased the transmission pulley and bearing kit from Parts Select. I got it the next day, without asking for next day delivery! When I took the old parts off (easy: pull off the plastic cover, remove the circlip and everything falls off the shaft (if you are working with the washer just tipped up. Unfortunately, that was where my easy repair ended. The parts were entirely different! After looking and looking and thinking, I called Parts Select. They informed me that Whirpool, who makes Maytag had redesigned the parts. They didn't look like they would work, but I followed the directions which came with the kit and installed the new parts - three times. The last time the pulley stayed on and the washer spun as it ought. The problem was that even with the smaller of the spacer washers the circlip was extremely difficult to get in its slot. Anyway, now the washer works and I am pleased, even though I spent many hours on what ought to have taken perhaps 1/2 hour.
All Instructions for the MAV7600AWW
241-255 of 417