LW8413L2 (PLW8413L2 A) Amana Washer - Instructions

first i removed the 4 screws that hold the motor in place.pull the motor out and disconnected the wires ,remove the belt from the pulley, when motor was out the work was very easy 3 more bolts that hold another element in place and the rest was piece of cake ...done thanks to parts select for send me the right part at first time i recomended and i received my motor in just 3 days.congratulation

This was my fist time attempting to fix a washer. I had to guess on the length of the belt since the model number on the machine had worn off and the belt had snapped in a way that made determining the length difficult. At first, I ordered a belt that was too small. I realized this after I was unable to remount the motor stand onto the bottom of the machine. This model had the motor assembly right in front of the unit. It was easily accessed after removing the panel on the front of the machine. It was easy to remove the 4 screws (they were all visible) on the motor stand. After that I was able to disconnect the pump belt. This machine has seperate belts for agitation and the pump. The pump belt must be removed in order to install the agitator belt because they both are driven by the same shaft and the pump belt is positioned on the bottom. There is also a tension wheel for the agitator belt which might be easily overlooked. Make sure to install the agitator belt so that the tension wheel is on the outside of the belt's path. The whole job is fairly easy if you have the right part to begin with. If you have to force the belt onto the wheels, then you probably have a belt that is too small.

The washer is four years old.
This is the second time I needed to replace this same drain hose on this same washer since I had the machine
There is only my wife ant myself maybe, 2 -3 medium size loads per week - why I would have two drain lines develop the same problem in almost the same location in two years is disconcerting
There must be a design problem with the clear plastic hose - Suggest Maytag go to a thick walled rubber hose
The hole is alway inside the washer on the bottom just after the hose bracket - I suspect that something rubbing causing a small pin hole to develop - when the condition first starts it is very difficult to located -There will be water under the washer
Run the washer and discharge the water - to locate

The replacement must be made through the lower front removable panel - and is easier to do if the pump return hose is also disconnected from the pump

Be very carful with the thin wall replacement hose - very light weight plastic - do not pull across the floor of washer - it could easily get damaged

Your company did a get job getting the part to me - The Fed Ex track system was great
I could tell exactly where the delivery was al all times -

I replaced the 7 springs holding the tub in place. To do this you have to take the two front bolts out the holds to front panel on the machine. Remove the front panel and you will see the bolt in each front corner holding the top in place. Remove these. Then remove the 8 bolts at the bottom of the three remaining sides of the machine. After removing these you can move the sides out of the way enough to remove each one of the 7 springs holding the tub in place. Then one by one replace the springs and put the sides back on in the order they were removed. Hopefully, if you are having trouble keeping your machine in balance in the spin cycle, this will fix your machine as it fixed ours.

I suggest if you are replacing the pump, order the belt at the same time, you must remove the pump to replace the belt.

Three brake pads are located just above the drive pulley and space symmetrically around the brake wheel. Remove the one screw per brake, slide brake out of brake wheel and replace with new brake. Apply silicone grease to new brakes before installing. Tools: 5/16 boxed end wrench.

Place black rubber adapter on the end of the drain hose and stick in the stand pipe drain. That's all.

Removed front panel.
Released 2 springs on belt tensioner.
Rolled drive belt off pulleys.
Unscrewed 4 bolts holding washer motor assembly.
Tilted motor to get at pump screws.
Removed 3 pump screws and pump slid right off shaft.
Aligned new pump and reinstalled screws.
Set motor assembly loosely in place.
Rolled drive belt onto pulleys.
Re-attached tension springs.
Installed motor assembly bolts.
Re-installed front panel.

** I should have replaced drive belt at same time, but it is working with no leaks.

Biggest trick is getting the agitator off. It seems like it is bolted on. I used a piece of braided cotton cord to run under both sides of the agitator and just pulled real hard. It WILL pop off.

Next the old seal will also seem to be attached. The edge is firm but not bolted. A small prybar will help.

Easy repair to do, but it did not fix my problem. I decided to get a new washer rather than go through further disassembly.

pull front cover off of machine, disconnect motor wiring harness. Remove 4 sheet metal screws holding motor / pump assembly to frame. Remove both pump hoses (caution - have towels and a bucket at the ready). Pull unit from machine. turn upside down on bench and replace components. Reverse for installation.

removed hoses from pump, removed 4 screws holding motor housing to washer, disconnected wiring from motor. It will make your life easier to re-assemble if you pay attention to how belt is located in relation to the legs of the pump. pump came off motor very easily. I had the old pump out and the new pump in and working in about 30 minutes.

To remove the drive bell, I drilled numerous holes through the top and split it apart with a screwdriver. The hub was really stuck and due to the unavailability of a 6" puller, I was forced to drill holes in the center section, tap the holes and use a harmonic balancer puller, PB Blaster, and propane torch to remove the hub. After removing the hub, I found small holes rusted through the outer tub. These I repaired with JB WaterWeld quite successfully. The new parts were well made and went on easily in about 45 minutes.

After removing the front panel I was able to reach the bolts holding the brake pads in place. Without the above mentioned ratcheting end wrench it would have been very difficult to start the bolts while replacing them. I would probably consider removing the motor if I had to do this again. It would give a lot better access. no real difficulty other than hard to reach.

Disconnect power and water, opened up front end by removing four self-tapping screws, removed the electric motor assembly from frame of machine, replace pump and belt and reassembled.

removed four 5/16 screws and two hose clamps. This released the pump and belt. With the pump on the bench, I removed a c-clip and removed the pulley. Just reverse the process and it was back together in about 15 minutes---total job.