LW8303W2 Amana Washer - Instructions

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part was attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.

Unplugged washer, turned water valves off, disconnected water lines from washer with adjustable channel-lock wrench. Water inlet valve was mounted on its own plate that needed removed using a screw driver. Disconnected the electric sensors and disconnected the outlet hose. Valve had to be taken off the mounting plate with a nutdriver. Replaced valve and reconnected everything. Water pumped in 10 times faster.

Disconnected wire harness. Loosened belt by slipping off main pulley. Removed motor/pump assembly (easy so far). Had some difficulty separating pump off motor shaft. Shaft had rusted into the plastic pump socket. Cleaned shaft with sandpaper. Reassembly with new belt and pump was easy.

Installing the new switch was a snap. With the dryer unplugged, open the top using a putty knife to release the 2 clips - one on each side. Lift the top and support it to stay open. Next, note the wire color and location for each of the 3 wires. Remove each wire from its prong on the bad switch by gripping the connector with pliers and pulling off. Next remove the bad switch by squeezing the tabs on the sides of the switch to release it. The switch removes to the front of the dryer. Install the new switch in the same method and reconnect the wires as before making sure the colors go back on the same prongs. I had to replace one of the connectors with a larger one (that came with the switch) since one of the prongs on the new switch was larger than the orginal (bad) switch. To do this, I cut the old connector off, stripped the end of the wire, and crimpted on the new connector. I had to be careful not to waste too much wire since there was very little slack to work with.

Removed the tub from outer shell/washer body completely. This made it easier to work. Removed the agitater by pulling upward. Used gear puller to remove bell housing and bell seal exposing the 1-1/2" nut holding down the hub. I remove the stainless steel tub liner exposing the hub assembly. Used the an impact wrench and 1-1/2" deep well socket to remove nut. Used the gear pullers to remove the hub assembly. It crumbled as I tried to remove it, so I used a dremel tool cutter and began cutting it apart. Removed the pieces with a chisel and rubber mallet. When the hub was finally removed' it was easy to remove hub seal and replace. Make sure everything is cleaned up, smoothed and lubricated before reassembly. I also replaced drive belt and pump. It was easy with outer shell completely removed. The washer went back together according to directions. Allow seal glue to set overnight and found there were no leaks.

First thing I did was to read the great information from other customers. John from Milton's post titled "frayed v belt" was excellent; so was Joseph from Goldsboro NC under the Pump part posts. I would add the following info which wasn't readily available. The Torx/starbit size mentioned in the posts referenced is a T25 the Amana lw8203w2 I have. I bought a t25 size torx wrench at my local hardware store for $2. I got everything together --the belt took some arm strength for an amateur like me to get on. Also, would recommend gloves as some of the edges are sharp down there. Everything appeared okay and when I started the spin cycle it started then cut off. I thought maybe besides the fan belt there was electronics faulty. However, I found an amana repair guide for my model online at scribd and under the troubleshooting section, it described the cutout of the spin cycle and if the new fan belt is too tight, it will bind and the spin cycle will cut out. So I opened up the front again and worked the belt for several turns to "stretch it" and voila, it worked perfectly.

Too simple to describe.

As described by your information. Also watched your videos about repair. Your web site is amazing and we WILL use it in the future. We have a perfectly running washing machine once again. Thank You!!

Removed old hose, drained the water from the hose. Put new hose on.

When the dryer stopped working, I checked the two switches to see if they were good. The start button checked out OK but the switch on the door read bad. Ordered the part with the part number and put on when it arrived. Just a matter of disconnecting and reconnecting three wires. Very simple