LW6143WM (PLW6143WM A) Amana Washer - Instructions

Remove 3 screws on Washer control top. Then 3 screws holding clear cover and removed. Remove 3 phillips screws holding face of panel on and tilted panel to get at wires. Marked the wire colors on eace of 4 terminals and removed them. Used plires to push the top on the switch near the knob and turned the switch counterclockwise. When the lugs lined up the switch slid out the back. Just reversed the above to reinstall following the proper colors on the wires to reinstall. Washer works fine now.

Unhooked the idler pully spring, removed the 2 hoses from the pump outlets, unhooked the idler pulley srring to slaken the drive belt tension, removed 4 bolts from the motor mount to drop the motor, and slipped the drive belt off the transmission pulley.

Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.

The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!

We noticed that water was on the ground of the laundry room. We initially thought that the washer was leaking. Realized that the washer was going on the spin cycle without draining the water which caused the water the slosh over the edges and then leak on the floor. Well, I had to remove all the wet clothes and suck the water out with a shop vaccuum-this actually took most of the time. After taking the front of the washer off, we noticed the water pump was stripped out. After removing the pump, we then noticed one of our kid's socks jammed in the pump. How the sock got there is still a mistery. We found the replacement part on PartSelect and ordering was easy and fast. Thanks. We're washing clothes again.

I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.

removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse

remove front panel. unplug motor. remove 4 screws and take motor,pump,idler and belt assembly out. remove pump from bottom of motor. 3 screws held pump and drove off with hammer. replace idler and install belt before new pump. install pump. reinstall assembly. works good now.

First I unscrewed the bottom of the front panel.
Then I realized the front panel pulls off from the top.
(manuals are helpful only if read!) I took the tub hose off at the tub and used my wet vac to remove all the excess water. (no towel needed) Using the appropriate size torx head bit, an extension and a small socket wrench to undo the screws holding the pump. I had to push and pull the bottom of the tub slightly to get proper room for the small socket wrench. pull the pump down and off. take the hoses off and place them on the new pump. reverse the process. tighten the clamps and replace the front cover.

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part was attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.

Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.