LW4302W (P1163301W W) Amana Washer - Instructions

Rear panel has to be removed to access part. Removing controls top of machine, two screws lower left and right, will make back panel removal easier. Back panel hangs on 2brackets,protruding thru the panel, near the top, and 3 screws across the bottem. You will also have to remove the drain pass thru connecting the internal drain hose to the external drain hose. The replacement part does not have matching screw mount holes to those on the rear panel. Their is a square punch out with a tab on the replacement which can be used for the top mount screw. Use a drill and bit to round the hole. Mount replacement then drill a hole in the replacement for the the lower mount screw. 1 day service and works like new.

First we turned the power off the machine and it took a total of 10 mins to repair. My husband use the pliers to pull off the stripped worn knob and replace it with the new timing knob and now I am a Happy Girl! Thank you so much, this was the only place I could find the part. We will certainly use you in the future.

Carolyn

Taking the hub out was a promblem because, with a puller it did not come out. It broke off while pulling out we had to drill it
out had to brake off.You need a 1 1/2 inch deep socket with a impact wrench. It was a hassel but got done. I replaced the whole seal kit and it is still leaking it leaks from the bottom of the tub. It leaks worse when it has a heavy load I dont know what to do.Need help.

I disconnected the water supply line to washer and moved washer into open area. I removed the front panel of washer to gain access to drain hose. I removed hose and reinstalled new hose. I did turn the hose holder inside the washer as it allowed the old hose to rub against the housing support of the washer causing the hose to leak. I was glad that I read the article that someone mentioned in their repair. The new hose was somewhat difficult to maneuver through the back of the washer and through the part that held the hose; otherwise, it was rather easy. Thanks for the feed back on your web page.

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.

Unplug the washer from the outlet. Remove two screws holding top of control panel and remove. Fold control panel forward as far as it will go, but don't force it. Remove 4 screws holding back panel down to washer, this gives adequate space to access the timer. Unscrew the knob from the front counterclockwise. Pull timer faceplate located under the knob straight off gently. Remove the two screws, (one on top, one on bottom), holding the timer to the control panel. Pull it out far enough to get a firm grip on the wire lead and disconnect it from the timer. Install the new timer unit in reverse procedure. When reinstalling the timer faceplate, notice that it only fits on one way. Look for, and match up the flat edges as you push it on. Be sure to rotate the timer to the top position before plugging it back in. For most of the work I used a phillips head screwdriver, flat head screwdriver, 1/4 in socket with a 1/4 in drive and extension. I am pleased with the operation and price of this timer unit!!

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

First I removed 2 screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I connected the new value and put it back in place. I then put the screws back in place.

This was very easy and it solved my problem

Thanks a lot

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

Removed motor apparatus with socket, took off water pump with star srewdriver . Installed new pump. Replaced belt. Schematic diagram big help...