LW2502G (P1118408W G) Amana Washer - Instructions

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.

removed all old parts, put in new, saved a bundle

Replaced the timer and knob. Very simple..!! Works great now... dont have to struggle turning the washer knob anymore.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Removed the cover on the washer controls. Loosed the knob and popped it off. Then disconnected the plug and replaced with the new part. Put th ekonb back on and closed it all up. It was pretty easy. Took longer to reomove all the screws than it did to remove and replace the part.

Followed video on PartsSelect website, they made it real easy.

Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.

We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.

My husband was the one who installed the parts but which gave him more problems was the hose.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

Removed the front panel, could see water leaking from the tub area near the shaft in the center of the machine. Dripping out once the water level reached the hub. Swing the top up, remove the large plastic ring at top of tub. remove the top of the agitor, pulls off easily. Remove the agitator with a firm pull up, not as easy but does come off. Removed the 4 bolt holding the tub. 2 broke off, but not to worry, the new kit has a complete hub. Pulled off the bell seal, pry up. Used an impact gun with 1-1/2" socket to remove the nut. The hub was frozen to the shaft. Tried a puller but ended up breaking the hub. I finally cut it off in pieces and pryed it off (the hardest part of job). Cleaned up the spline with a small file and patience. Installed the new seal kit. Ended up buying the M800 3M sealant on line. I went this far, another $40 for that. Fitted it all back up per instructions. No leaks. All good.

Diagnosing and ensuring that this was the problem took much longer than the actual repair. This was a simple repair, removal of six screws to access the timer assembly, two small bolts hold the assembly in place. Very easy to access and replace.