LW2402 (P1110516W W) Amana Washer - Instructions

Unscrewed the old one off and then screwed the new one on.

First we turned the power off the machine and it took a total of 10 mins to repair. My husband use the pliers to pull off the stripped worn knob and replace it with the new timing knob and now I am a Happy Girl! Thank you so much, this was the only place I could find the part. We will certainly use you in the future.

Carolyn

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

It was easy, All we had to do was loosen up the tension on the pump, put the new belt back on and put the tension back on the pump motor by sliding it to the side and re tighten the screws to hold the pump tight.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Un plug machine. Turn off hot & cold water. Remove the front panel by removing the 2 screws at the botton & lift front from the bottom until it unhinges from the top. Tilt the washer back far enough to put a contaner to catch the water left in the hoses. Loosing the hose clamps so the water comes out slowly. If you remove the hose to fast your container won't catch the water. Do one hose at a time. Next disconnect the wiring harnes from the motor. Remove the 4 screws holding the pump/motor. Disconnect the belt from the washer. You will have to tilt the pump/motor to get slack in the belt. Remove the pump/motor & the belt will come with it. This is when I found that the belt was toast & I had to order a belt. Paid shipping twice. once for pump & once for belt. Seperate pump from motor by removing 3 screws. My pump came right off. Reverse the operation to install. REMEMBER TO PUT THE BELT ON BEFORE THE PUMP.

Washer is old, but in very good condition. PartSelect was the only company I could find that had a replacement part. That included checking with Amana delears and other repair companies. The sequence of repair in 11 steps: 1. Unplug the washer. 2. Remove 6 philips screws (3 top,3 bottom) from the front of washer control panel to release the control panel. 3.Remove ground wire clipped to the timer. 4.Remove the knob. Could not unscrew,so I placed the tip of screwdriver against the end of the shaft on the backside of the bad timer and tapped to remove the shaft. 5. Use a 1/4" nutdriver to remove 2 screws securing the old timer. 6. Squeeze end tabs and remove control wiring plug. 7. Reverse steps 7 to 4. 8. Unscrew old shaft from the knob 9. Replace timer face plate (keyed to match new timer shaft only goes on one way). 10. Screw knob onto new timer. 11. Reverse steps 2 and 1. Note: It took me twice as long as it should of, I had the assistance of my 2 year old granddaughter Malae.

Followed video on PartsSelect website, they made it real easy.

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

I removed the screws that held the timer/control cover in place. Removed the two screws that held the timer and unplugged the wires. I discovered that the old knob had jammed the timer shaft, so I probably didn't need a new timer. However, I had one ;-) so I installed it along with the new knob.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

Unplug the electrical cord. Remove the front cover with two screws at the bottom. Unhook the front two springs on the tub that secure it to the floor of the machine. Tilt the tub back as far as possible. Remove the electrical connector to the motor at the motor with the plastic tab release. Remove the four screws that attach the motor mount to the floor of the washer. Unhook the two hoses that attach to the pump on the motor bottom. Catch the water in a towel or in a flat tray. Unloop the belt from around the pulley on the bottom of the washer tub shaft and remove the motor, pump and belt as a unit. Remove the brake pads by removing the single bolt atop each one and pull it out of the machine. This will take the longest amount of time. You will have trouble getting the new pads in position, especially the one at the back. You many need to gently spread the brake disks to allow the pads to enter using a padded screw driver. Lightly lubricate the new brake pads before installing with silicone grease and replace the bolt and grommet with the new ones provided on each. Using a torx screwdriver, remove the pump from the motor and discard the worn belt. Remove the idler pulley using snap ring pliers and replace with a new one. Install the new belt and idler. Replace the pump with a new one, or reuse the old one if it seems in good repair and is not too old (mine was 15 years old--I replaced it). Remount the motor, pulley and belt on the machine and secure with 4 bolts--loop the belt around the main pulley on tub shaft. Reattach the hoses to the pump. Reconnect the electrical supply to the motor. Rehook the two spring to the front of the tub. Plug the washer back into the wall outlet. Pour in a couple of gallons of water into the tub before starting to ensure that the pump does not operate in a dry condition. Start and test operation. Be Happy. Wash hands and have a cold one.

Turned off water & unpluged ac power. Removed 2 screws on front panel. Removed panel. Found peices of V belt. Removed 4 screws from electric motor which allowed the belt to come out. Ordered new belt on line. Received the item in one day. Reversed the above sequence above. Now the washer is running as good as new.