Models > LGR6646BW1 > Instructions

LGR6646BW1 Whirlpool Dryer - Instructions

All Instructions for the LGR6646BW1
1561 - 1573 of 1573
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would not heat up all the time
The dual cil gas valves were out of resistance range. The new coils were easy to install with a screw driver, sockets set and multi-meter.I checked the coil resistance and one of the new coils were a little high, but I installed them and they have been working fine.
Parts Used:
M Series New Style Coil Kit
  • Robert from Hampton, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
one of the Drum rollers was bad and the belt was broken
watched the repair video and had no problem doing the repairs. they were VERY helpful!
Parts Used:
Rear Drum Support Roller Kit Multi Rib Belt - 92-1/4"
  • John from Christopher, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
my dryer stopped tumbling
so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me
Parts Used:
Idler Pulley Assembly Multi Rib Belt - 92-1/4"
  • joann from woonsocket, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't start
Watched the tutorial online. Took the back off- replaced the fuse. Put the back on . It was extremely easy !!
Parts Used:
Dryer Thermal Fuse
  • Rhonda from Oconomowoc, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Replaced Belt
The online vidio was very helpfull
Parts Used:
Multi Rib Belt - 92-1/4"
  • MARCUS from MACON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the dump would not stop running.
Replace the switch in diagram #4.
Parts Used:
Dryer Thermal Fuse
  • modean from Clermont, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer tub drive belt broke
Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!
Parts Used:
Multi Rib Belt - 92-1/4"
  • Ray from Salisbury, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer overflowed
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.
Parts Used:
Leveling Foot
  • Beth from Valley Springs, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't turn on
When the part came in. I unplugged the dryer. Pulled it away from the wall and took the back off. I pulled the wires off the old fuse and plugged them in the new fuse, then unscrewed the on nut that held the old fuse. Then slid the new one in and put the nut back on. Plugged the dryer in and it worked. So I unplugged the dryer and put the back on.
Parts Used:
Dryer Thermal Fuse
  • pamela from ocean springs, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would run, but not heat
Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!
Parts Used:
Dryer Thermal Fuse
  • Kenny from Euclid, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Parts Used:
Door Catch Kit
  • Charles from North Chesterfield, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Indicator lights blinking, not drying, auto settings not working
Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.
Parts Used:
Dryer Thermal Fuse
  • James from Frankfort, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Parts Used:
Door Catch Kit
  • George from Melbourne, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LGR6646BW1
1561 - 1573 of 1573
Back to Top