LER1115AAW Admiral Range - Instructions

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

used the supplied parts...very easy. The parts were exact replacements.

Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

turn off breaker take two screws loose from back of oven slowly pull out element unplug element an plug new element in push element in place an put screws back in turn on breaker done

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements

I've been trying to remove the bracket at the roof of upper oven so I can get to the broiler element itself. The screws are in place so tight, the won't move. I've used regular as well as ratchet screwdrivers and the screws still won't move. I don't want to spray WD 40 in oven because of a possible fire hazard, so I haven't changed out element yet. Tried calling customer service for advise, but to no avail. All other screws loosen easily. What should I do next.

Went down stairs and turned the breaker for the oven off. Opened the oven door, took a phillips head wrench and took two screws out of the back of the oven that held the element in place. Slowly pulled the old element toward me. It seemed to catch on something in the back of the oven on the other side of the oven wall, so a jiggled the old element a little and it came out towards me with a mechanical connector and a wire attached at both ends of the element. I slipped the connctors off of the element and attached the connectors to the new element. Carefully slide the new element back through the holes and put the screws back in the small plates attached to the element. Went down stairs and turned the breaker back on. Turned oven on and it heated up even quicker than the old element.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were working and they did.

Turned off the circuit breaker. Removed two screws - pulled the element out enough to get to clips connected to power. Removed old element - installed the new one. Replaced the screws, then turned the circuit breaker back on. Stove was repaired.

Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Removed burner and then burner pan.Then replaced pan and reinstalled burner.