LD-6100WB1 LG Dishwasher - Instructions

I am 77 years old and got it all on but the corners did not want to go in so I had to call my grandson and he got them in. It still leaked on the bottom left side. It is getting old (11 yrs) so I decided to get a new one. It is actually pretty simple to install, but it does take a little strength.

Took off the broken one and snap on the new one.

snapped on new axel-wheel assembly

Very easy repair. First remove all the screws from the inside of the door, making sure you support the outside part of the door with a pot under it on the floor. Pull the locker part out, remove wire connection with needlenose pliers, and install replacement part. Put door back together, and you're done.

Old door seal appeared ok, no rips and seated evenly all around. Pulled that seal out and replaced with new. Seated new door seal after wetting inserted lip. Tested...leak greatly reduced, but still dripping. Removed seal, placed a rubber rope (same rope used for screening) within the tub recess, then reseated new seal. leak ceased. Also replaced the reservoirs on the left side of the cabinet (guide assembly). Old reservoir had debris within so decided to replace. Used regular pliers for the 3 hose spring clamps underneath, and a pair of large neede nose pliers for the fill flange (regular thread).

Very easy just took out two screws that held the dishwasher to counter top.Then pulled dishwasher out just far enough that both door cables are exposed.The hardest part for me was getting the spring stretched enough to clip on.This was a easy installation for most people.

connector was broken. just attached new connector to spring on each side of door. easy fix.

Replaced it . Simple

Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.

Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws. I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.

All I needed was the rinse aid cap, damm shame one must pay $75 for for the complete rinse aid dispenser just to replace the cap. I will not purchase LG product again. The cost to just replace the cap is a rip-off.

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope

I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.

Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.