LAT9356AAE Maytag Washer - Instructions

Watched the installation video on the website and used exactly the same technique. Belts came off easily as did the pump assembly. Installed the new pump and belts and adjusted the pump belt tension to 1/4 " when squeezed together. Replaced the front panel and moved washer back into position. The pump noise was gone and there were no leaks. Easy job.

searched on line for the part.you guys had a very informative video looked how simple it was i purchased the part i needed and the rest was history thanks you guys are great saved me around 140.00 bucks. for about 15 minutes worth of work

just removed old base assembly with nut driver on one screw and put new base on .

pulled out washer from the wall tilted back towards the wall. removed front panel by pulling it out at the bottom. .removed belts by spinning the pulley .similar to taking a bike chain off. cleaned all pulleys with a degreaser 409 etc. springs are under the motor. slide motor away from you. remove springs with needle nose pliers from the front. to install new springs hook them to the rear of the motor first. fish them under the motor then grab them with needle nose pliers and hook to the front of the bracket. you could also tie a fishing line to the front of the spring and pull it thru that way. install belts [very easy]. did not need plastic guides. i did not install

Love these older machines... Easy simple and straightforward. Lay the product front up on a small 2 X 4. Remove front cover, (two phillips head screws near bottom). reach under hand roll off both belts,, check belt numbers to ensure old belt numbers with new belts. Rolled on new belts, checked tension, per enclosed note. Ajusted belt tension via the pump. replaced front cover and screws. Install unit, (be sure to level it) Time to Rock and roll.

I followed the step by step instructions on the video and it worked to a (T). You guys are the best. Thank you for all your help. Sincerely Eddie .

I am not going to describe the repair. The video that Part Select has on their website is exactly how our repair went. Very simple. This is the second time we have used Part Select. They have saved us a lot of money on repairmen or new purchases. I would definitely use them in the future. The videos are so easy to follow anybody can make the repairs. Also, the delivery company not only misdelivered the part but, they damaged it. When I called Part Select about the part being damaged, they immediately sent out a new part without any questions. Why aren't all companies this awesome?!

I watched the video and everthing went pretty well. The only problem I had was removing the Clamp Nut. My Washer is more than 10yrs. old so there is a lot of water and lime build up. I use a Cole Chisel and a Ball Pen Hammer to break the Clamp Nut. Because you can dispose of it anyway a new Clamp Nut comes with your Mounting Stem/Tub Seal Kit. The Tub wrench comes in handy for removing the Mounting Stem and to reseat the Mounting Stem. You are also going to need the Tub Wrench for reseating the Clamp Nut. You can order a Tub Wrench online there are various web sites.

I hastily (miss diagnosed) the symptoms by assuming that the Drain Pump was in fault, Ordered the Drain Pump part online on Sunday got it early on Wednesday. Installed the Drain Pump but the timer would not move. So back to drawing board. Got on the phone with the nice people on PartSelect ordered the Lid Switch Assembly. Got the part in less than 20 hours To install the Lid Switch assembly remove the back panel by removing 3 sheet metal screws at the top and 2 at the bottom now you will have access to all the wires and the Lid Switch Assembly. It is attached with one sheet metal screw. The hole in the Assembly is slotted so you may have to slide it back and forth for the switch to get activated when you open the door. Installed the part, plugged the washer machine in filled the tank. The washer machine came alive the timer was moving (the washer machine start working again). This washer machine should be good for another 20 years. By the way this was the first breakdown on this washer machine after 20 years of service. Thanks PartSelect for well trained people and prompt service I couldn't have done it with out your help.

Removed old hose and replaced with new one.

Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

Replaced the pump. The front panel screws were rusty. I also replaced the belts at the same time. The repair video told me just what to do. I wouldn't have known about the belt tension otherwise.

Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Moved washer away from wall. Removed rear panel (4 screws). removed hose bracket (1 screw). use vicegrip to "open" hose spring clamp. Removed old hose, slipped spring hose clamp over new hose. "Opened" spring hose clamp put new hose over washer drain, released vicegrip. Assemble in reverse.

Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.