KUDI01ILBL6 KitchenAid Dishwasher - Instructions

remove old seal, clean and dry the gap where the new seal will be installed. Apply adhessive, place new seal, then let dry for 24 hrs.

The hardest part was getting the seal, we first ordered from a sears parts store locally. They also told me that everything was included to install it, but they did not include the adhesive, they lost the order via ups and never notified me. I finally called them and they made me go back to the parts store for a refund. I then ordered on parts select and they had it in my hands in 3 days.

I first thought I may have a defective water feed tube that runs from the bottom of the dishwasher tub aolng the back to the top. This is what the top rack sprayer plugs into to get water.

This was easily replaced by uncliping the feed tube by the two clips, one on the top of the tub and one in the back. You then give the feed tube a twist clockwise about 45 degree (relative to the bottom of the dishwasher). This will remove the feed tube and bottom sprayer.

However, this didn't fix the issue.

I then replaced the pump/motor. This is done by uninstalling the dishwasher and flipping it onto it's back so you can look at the bottom of the dishwasher. There is an electrial connector on the right side that needs to be disconnected. The motor is help on by one bolt in the back and a socket wrench with extender will be needed to get to it. Once the bolt is removed, and motor needs to be twisted about 45 degress so it feels "loose". Then you need to pull straight down and the motor will come off.

Just reverse all the steps to install the new motor.

But that didn't fix the issue either.

Come to find out, the problem I was having was the grinder screen was so gummed up with paper, the grinder broke and water was not getting through the screen. Here is how you replace the grider (which was the true fix to the problem).

- Remove the feed tube like I listed above. You DO NOT need to uninstall your dishwasher.

- Use a Torx driver to remove the three visible bolts on the bottom of the washer tub.

- Pull up on the plastic piece you just removed the screws to remove it.

- Use a smaller sized Torx driver to remove the one screw from the Grinder plate. Once you have the screw off, use a pair of pliers to pull straight up on post sticking straight up on the grinder housing.

-You can now see the grinder. Pull the screen and grinder assembly out. If it is still intact, just clean it and replace it back into its groove. If it is in pieces, it is destroyed and buy a new one.

- Reverse all the steps to put the dish washer back together.

This screen that fits into the groove was jammed up with paper and was causing my my issues. Once I placed this the macine worked great.

Each Molded one-piece plastic upper dishrack wheel mount includes a tiny plastic spring clip which hold the mount in place on the upper dish washer rack.
These clips become dry and britle over time and snap off.
Because they are molded in the wheel mount itself you have to replace the entire wheel mount assembly

The air inlet strip has a flap and two smaller side flaps that seal the bottom of the inner door to the bottom pan that hold the water. The flaps don't form a watertight seal as they only serve to prevent the water surging during wash and rinse cycles from splashing out of the bottom pan onto the floor under the door. What I learned after dismantling the door is that the problem I was having with water dripping from the bottom of the bottom of the outer door was being caused by a loose upper round louvered vent and not he lower vent strip. If the lower vent strip were the problem, water would leak from the front lip of the bottom pan, which is located well behind the face of the front door panel.

Here's my recommendation on the lower vent srtip repair. Turn off the power to the unit at you breaker panel. The air inlet strip is fastened to the backside of the inner stainleess steel door panel. To access the screws the outer door panel must be removed. Open the door and remove the six torx head screws that fasten the outer door panel to the stainless steel inner door. Don't remove the two torx screws top dead center as they hold the door latch. After removing the screws, raise the door up to the nearly closed position. Lift up the outer door panel handle and door bottom to disengage the outer panel from the inner stainless door. The next part is a little tricky since the vent strip hex head screws are at he bottom of the stainless door panel, facing out with the door closed. The lip of the bottom stainless pan is high enough to make it a tight fit to access the screws. There is also a steel bracket that is a door stiffener and holds electrical wiring. I found removing the bracket held by a 1/4" hex head screw on each side made access to the vent strip scews easier. Lay flat on the floor. With a 3/16" nutdriver or socket wrench each of the five vent strip screws can be removed. It's a tight fit between the bottom lip and door bottom, but it can be done. Remove the old vent strip and attach the new one. Make sure it fits snugly into the slot. Best to have an extra pair of hands at this point to hold the stip securely in place while screws are reinserted from the opposite side. Reassemble everything in reverse order.

It was when I had the outer door panel off that I noticed my problem was water getting past the upper round louver vent seal and thus running down the inside of the outer panel. Simple fix was to remove and clean the scale residue from the parts and door. Then reassemble the vent and twitst tighten the vent to compress the rubber seal on the inside face of the door.

SAFTY: Turn water off. Flip the circuit breaker.
PREPARE FOR REMOVAL: Unscrew / Remove kickplate. Disconnected water connect just behind the kickplate. Be ready with a couple of dishtowels. Pull the door down and remove any screws that go into the under part of your counter top. Jack the front legs screw down.
REMOVE: Gently pull the Dishwasher from under counter. Push the insulation flat against the side of the dishwasher about every six inches that you pull the dishwasher out to prevent it from snaggin on the cabinet face edges. Remove the baskets and spray arms. Careful not to damage the heating element.
NOTE: Here I noticed that the guy who installed the dishwasher kinked the copper line limiting the water into to my dishwasher. So my circulation pump/motor was probably running dry. I replaced with a flex type "dishwasher" hose that will easily coil up behind / underneath without kinking when I push back in. DO THE REPAIR RIGHT - DO IT YOURSELF!
REPAIR: I gently laid the dishwasher on it's side (cardboard underneath). I disconnected the power - 2 wires. Then, I only disconnect one wire harness, the sump tubing and the I thought I'd better remove the impeller that the sump tubing was connected to (it was only attached with one screw). Remove the 3 plastic clips around the pump/motor. Carefully push the pump into the dishwasher. DO NOT LET THE PUMP FALL AS IT MAY DAMAGE THE HEATING ELEMENT IN THE DISHWASHER! Push the new pump/motor in place until the seal is at least flush with the bottom. I used the back of a wood spoon. Don't pull on any part of the motor from the bottom or you'll break the thin aluminum casting. Just inserting the plastic clips back in place will pull the seal flush with the bottom again.

I was lucky. I simply removed the motor/pump, replaced it with the new motor/pump, and put everything back together in reverse. I put a little bit of silicone grease on the o-ring of the temperature probe. I happened to have some silicone grease because I also have a pool.
Done. It cost me $220 Vs. $550 quoted by Sears. That doesn't count the extra Sears would have charged my for repairing the kinked copper line. And you know they would've kinked it again. That only cost me $20 more and the flexible line couldn't have been easier to install. I could have done the whole thing for less but I opted to replace the pump/ motor together.
Getting it all done right, no leaks, no kinked line, keeping the dishwasher that matches the other appliances (VS. replacing it at $550 repair price), all less than 1/2 the price of a quoted repair - PRICELESS. - THANK YOU PART SELECT. DISCLAIMER: I have no affiliation with Part Select.

Removed mushroom shaped float cover by simply pulling up. Cover simply slide down into switch which is mounted through the floor of the tub. Using an adjustable wrench loosened and removed plastic fastening nut allowing removal of switch assembly from below. Disconnected two wires from switch and attached replacement assembly, reinserted in mounting hole, reattached nut from top, reinserted float cap and job done! The only tricky part is that the switch needs to be mounted inside assembly, wires connected and snapped shut before reinserting. Not difficult once you figure it out, Also need to make sure rubber washer is inserted on the overflow tube before reinstalling. Keep track as you remove and simply reverse the order. Tried to obtain part locally and was told it would be 6-10 days before delivery. Order from Part select arrived in 2 days.

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

First I checked the power supply and noticed the breaker was not tripped. Confirmed the unit was getting power. I then downloaded a parts breakdown from the Kitchen Aid website and noticed there was a fuse mounted in the control section. Using my digital multimeter I confirmed there was no continuity through the fuse. I then ordered the part, installed it and washed a load of dishes:-)

the parts only took a few days to arrive, and it took me about 2 minutes to install them-no tools were required. i took out the end plugs from the slider bars, slipped out the old broken wheel parts, snapped on the new ones, slid the upper rack into the slider assembly, popped the end plugs back into place and VOILA!!

aside from the expense of the parts- much better to go this route rather than hire a repair guy to do it!!

Recoved the screws which secured the handle assembly (approx 8). Removed the old parts and screwed home the new parts and replaced the assembly. Worked perfectly.

The hardest thing for me was to decipher the model number as they use '1s' and 'Is' and you can't tell them apart.

Also the part diagrams should have each part number listed to make it easier. Took me longer to work out what to order than do the repair.

Didn't have to remove any screws, etc. Just had to pull the old gasket out of a grove in the top and sides of the frame, clean up the particles caused by the deterioration of the old gasket, and install the new gasket. Have to be careful to start at the top center of the frame exactly in the midpoint of the gasket and carefully push the gasket into the grove with your hands. Try not to stretch the gasket. There will be about 2 inches of extra gasket laying on the bottom on each side of the dishwasher, and that is OK.

Pull the dishwasher out, unscrew the old wheel assemblies and screw in the new ones, that easy, anyone could fix this problem, it is a poor deisng though, the inside of my dishwasher is stainless and the only thing to go bad are the plastic parts

We replaced all four. You unclip the two front parts on the top drawer to pull it all the way out of the dishwasher. Unsnap the old mounts and clip the new ones on. Slide the top drawer rack back in and replace the two front clips.

This was truly an easy repair!

Switched circuit breaker off.
Removed kick panel.
Removed the dishwasher from counter.
Disconnected drain hose from the pee trap.
Disconnected drain hose from pump.
Installed new drain hose.
Reinstalled dishwasher in counter.
Connected hose at the pee trap.
Turned power back on. test for leaks by running a cycle.
Reinstalled kick panel.

Took stop off end of track by smooshing spreader things together with butter knife, so they would fit through holes.
Maneuvered wheel on track and clip on rack. Put the stop back on.