KUDI01FLWH6 KitchenAid Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic cable broke due to age/wear.
I noted that the replacement kit had two large rollers now vs the original that had only one that rotated, the other fixed. Also, the plastic attachment for the door arm was more simple. It was very easy to pull out the unit, attach the spring end hook to the rear of the dishwaser frame hole, attach the new cable, thread it over the two rollers and pull the spring using the cable to attach to the door arms. Less than 20 minutes to install both sides.
Parts Used:
-
John from Benicia, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
left side door balance repair
Disconnected the water line after removing all the screws which hold the dishwasher in place. Slid the unit out around 24 inches and removed broken Door balance pulley and replaced both sides with the new door balance set . replaced both sides to ensure an even and balanced tension when opening and closing the door! Over all a relatively easy repair. Just be certain you disconnect the water line if you do not have enough slack when pulling out the unit from the cabinet. Good as new!
Parts Used:
-
Nino from Neshanic Station, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Dishwasher smelled and not cleaning dishes
The video was excellent as was my experience when I replaced my ice maker.
Parts Used:
-
Mark from Las Vegas, NV
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Old motor making lots of noise. Replace with new one!
Pulled out, put on it's side. Take pump off and put new one on and put all back together. Very easy. Video was helpful also.
Parts Used:
-
Kathy from Northfield, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
track stop broke
-
Denise from Chico, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Not cleaning properly and loud noise
Followed the video and changed it out in 20 minutes which did not fix the problem entirely, but I went back to the list of symptoms and watched a video on exchanging the Chopper assembly. I disassembled the interior and found broken glass and wire and string restricting the rotational functions. No replacment was necssary here, but a good cleaning was in order. This made it run like new and the glasses came out shiny again. These step by step videos have even made me think about becoming an appliance repairman. LOL! This is about the 8th time I have had success with Part Select. I have had no failures. Thank you for giving away all the secrets. YOU DEFINITELY HAVE SAVED ME AND MY FAMILY TONS OF MONEY!
Parts Used:
-
Clark from Surprise, AZ
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door would fall open, no spring tension.
Removed under countertop screws and lower trim plate. Retracted levelers to clear slate floor. Could only pull unit out about 8 inches, so had to reach in blind to remove and reconnect link ends from springs. Other than my 1 year old Newfoundland pup 'helping', no problems. Parts were perfect fit, just like in the video.
Parts Used:
-
Ralph from Ball Ground, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!