KUDE40CVWH3 KitchenAid Dishwasher - Instructions

After I took apart the inside of the door, removing 12 star screws, I was able to see the inside of the automatic soap dispenser device. Since I now had the new device to look at, I was able to replace the latch pin back in the existing device and it worked!

I now have a replacement if the device actually breaks in the future and looking at the small plastic pieces, it will probably happen sooner or later.

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

Take 10 lower star srews from inside of door (5 per/side) that hold on front. Remove front door panel. Remove 6 screws in detergent dispenser and replace.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

After reading other posts I opened the dishwasher door put a support underneath it. Knowing that all the screws were not the same I carefully unscrewed them and placed them on a towel in order of extraction. After all the screws were taken out, I lifted the door up gently and lifted it out of its place and put it aside. Now I could see the hex screws holding in the soap dispenser. I then unscrewed the screws and place the frame aside. Next I gently pulled the electrical connector to the dispensing unit off. After locating a snap tab on top on the left hand side and one underneath on the right hand side, I gently lifted the tab and the dispenser unit moved slightly forward. After gently prying the lower tab on the right hand side the dispensing unit was loose. I just reversed the process to put things back together. I was not necessary to have any help taking things apart but it was very helpful having a second set of hands when we put it back together. Lining up the screws for the door was much easier with two people. After installation, I started the dishwasher to check for leaks. Everything was fine. Very satisfied to be able to repair/replace this unit without calling a tech. If you can change a spark plug on a lawnmower you can replace a soap dispenser on a dishwasher such as mine. Very quick delivery from parts source. Thank you.

Soap dispenser unit could have been repaired by pushing the plastic arm back home and adding two drops of instant glue to keep the plastic shaft in proper place. Didn't need to purchage a new unit.

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Remove front door panel, replace B-metal fuse.

Just snapped it right into place! No tools required. Very easy!

The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video