KUDC03IVBL0 KitchenAid Dishwasher - Instructions

Used a video to guide me.

Removed 6(six) torx head screws backside of top control panel. Removed top of panel to access contol board. Unplugged clearly marked wire plug-ins. Unsnapped control board, snapped new board in ressymbled panel.

The part was easy to install. But , you might have to unhook electrical, water, and drain. That is the time problem, part install is easy. All I had was a socket set, 1/4, drive fits. But a nutdriver would have been easier. WATCH the install video, great info!!!!!

Took old basket out and put new basket in took less than 5 minutes

Remove power to the machine. My particular installation did not require physically removing water and drain lines. Remove the dishwasher from the cavity. Put a towel or two down on the floor. Lay the washer on its face on the towels and this orients the motor in the up position on the bottom of the washer. CAREFULLY unplug the motor wiring harness but if possible, leave the heating element connection in place as spade connectors tend to lose their grip with multiple engagements. Remove the single bolt located between the motor and stainless bottom of the cavity that locks the motor in place. Leave it in the cardboard shield, that really helps in reinstalling it. CCW rotation of the motor disengages it from its housing. Work the motor straight up and out of the housing. This was the most difficult part of the entire process due to the metal housing not quite clearing the plastic pump housing where they mate, but its do-able. Nothing should have to be forced. Now you have the motor in hand. Be very attentive how and what order you disassemble. Remove the back of the motor housing to block the armature to remove the impeller. DO NOT NICK THE FIELD WIRING IN THE MOTOR. I believe the threads were left hand but I don't remember the rotation. They do tighten in the direction of the motor rotation though. Carefully pry the seal out of the pump housing with many short lifts as to not mar the housing itself. Added a little dishwashing detergent on the outside of the new seal and carefully pushed it into place with the end of my screwdriver. Don't cut yourself on the metal insert in the center of the seal.Reassemble the impeller to the shaft WITH the spacer that comes with the new impeller kit. Make sure the impeller is tightened down completely to the end of the threads to insure proper clearances when reassembled. Don't force or over tighten. You'll feel a positive stop. Reassemble the motor to the housing Lubricate the housing o ring seal on the outside with a VERY small amount of dishwashing liquid lest you create a suds factory on startup. Replace the holding bolt on the pump housing. Reconnect the motor leads and heater element if removed. Stand the washer back up. There will probably be water around the door area from the pump when the machine is returned to the upright position. Reconnect lines and check under the pump housing for leaks while in operation being careful not to get into moving parts or electrical connections. Good luck.

Followed video on your site rapair was the same as the video

The most direct way to do this job is to completely pull out the dishwasher so you can get to all the parts involved. However, I didn't want to break and make all 3 connections. Having installed it using braided hose for the water line, I had enough give to pull the unit out about halfway. This exposed the pulleys and door hook, but the spring was still in the back (and had actually fallen off the frame and was now lying behind the frame on the floor. So a little back and forth and I was able to retrieve it. I hooked the link on the end and blindly and miraculously hooked the spring into it's hole on the frame. Since I had no room to work with the door open, I had to keep it closed which meant the spring was under full tension. This is where the drum stick came in. I pulled the spring forward with a pliers and shoved the drumstick in the loop on the spring and held the stick against the baseboard while I threaded the string around the pulleys and onto the door hook. I guess I could have tried a long screwdriver, but the drumstick was handy and the bulbous tip prevented the spring from sliding off

I started my repair by replacing the most likely and least expensive cause of the problem and replaced the bimetal thermal switch. The PartSelect video was very helpful on doing this repair. However, this did not correct the problem and I decided to try again and risk replacement of a much more expensive item, the electronic control board. There was no video for replacing the control board but I had gained knowledge and confidence from my efforts with the thermal switch. I ordered the part, it arrived in 2 days and I successfully installed it with no difficulty. My dishwasher has worked fine for several cycles now so I consider the problem fixed.

Our Kitchen Aid dishwasher was not getting the dishes clean so I went on line looking for a fix that did not include replacing the dishwasher. Found the Parts Select website, read a few of the comments and ordered the pump / motor assembly. Following the steps of others, I turned off the dishwasher at the breaker panel and disconnected the power. I found it easier to disconnect the water feed and drain under the sink rather than under the dishwasher. The dishwasher was held in place with 2 screws at the top, It came out easily. Warning: have towels handy as the water in the drain, inlet and housing will come out with the removal of the dishwasher. I did have to remove the upper spray assembly, easy, to remove the motor / pump assy. the assembly is held in by three plastic clips. When these are removed, the assembly pulls out through the inside of the dishwasher. Replacement was simple, just reverse the steps in removal. Be careful to center the pump / motor assembly. Having done this once, I would probably leave the dishwasher in place and change out the pump / motor assembly.

I followed the directions already on your site. They worked perfectly. It was easy. The only trick was that I needed a Starz driver bit to remove the screws holding the panel in place. Luckily I had the right one.

took out old one and slipped in the new one

rinse cap was put in and turned to secure.

Replaced the Pump Motor and Housing Assembly. Generally the video did very well in showing what to do. However, it underrated the difficulty of getting the assembly to fit properly and seal in place. The clamps to secure it were difficult, but eventually got it through about 5 repeated attempts. Now after first us, it is working well.

followed instructions in pkg.