KSRA25CNSS00 KitchenAid Refrigerator - Instructions

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

as shown in instructions

This was the easiest repair I have ever done. Don't waste your money calling a repairmain for this one. Unplug from electrical outlet, and turn off water supply. I first removed the ice bucket to give myself the room needed to remove ice maker. Then I loosened to two top nuts holding the icemaker and removed the bottom one. Pulled the icemaker away from the freezer wall and disconected the power supply. Removed unit from freezer and removed the three screws holding control motor assembly in place, gently removed icemaker control assembly. Secured with the three screws, placed unit back in freezer making sure water inlet was in place and reconected power supply. Slid unit onto the top two nuts and tightened and replaced bottom screw. Turned on water supply and reconected to electrical supply. Easier then pie.

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

Removed the icemaker assembly, which was simple to remove. Once the assembly was removed, I unscrewed the motor housing and replaced it. I then reinstalled the assembly and closed the door. It did not making ice immediately and it took about 30 minutes to start.

followed a movie on the internet. I'm 77 and I felt like it was very easy. My wife of 51 years gave me a round of applause when the first ice cube popped out.

I pulled the refrigerator away from the wall, unplugged the electrical cord, and turned off the water going to the refrigerator. I then removed the cover on the bottom rear of the refrigerator by removing 7 or 8 small screws. Luckily the new and old valves were exactly the same except for some color coding. There were 2 screws to remove that attached the valve to the body of the fridge. There were 3 plastic tubes that connected to the valve and 2 wiring harnesses that plugged in. Before removing them, make sure to note which tubes and wires went where. The 3 tubes on the old valve were the push in type, just like the new one. I could not pull 2 of them out like the instructions said. I had to pry them out with a screw driver. In doing so I warped about 1 inch on the end of each tube which I then cut off with a razor blade. The electrical connections pulled out easily. I then pushed each tube back into the new valve which was very easy and pushed the electrical connections in. I attached the valve to the fridge with the 2 screws, turned the water on, plugged in the electrical cord, and checked for leaks. I put the back cover on and was back in business. It took me about 40 minutes but when I was younger could have done in in half the time.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

Unpluged the refrigerator. Removed the cover on the control unit by inserting a screw driver under the metal clips. Removed the three screws frrom the front of the control unit. Pulled toward the back of the refrigerator on the metal loop which turns the icemaker on and off and it came loose where it goes into the control unit. Wiggled the unit and it came free. place the new unit in approximately the right position. Reached into the icemaker and moved the ice eject leavers so the shaft would enter the control unit with the flat side of the ejector in the right position. Gently pushed the control unit into its place and aligned the screw holes. Replaced the three screws. Inserted the wire shut off loop into the hole on the back of the control unit housing. Pluged in the electric. The ice maker worked.

Followed instructions on video on website. Very easy to do. Removed old part, put in new and it took all of 15-20 minutes. Had ice in approximately 1 hour.

removed the ice bin, removed small screw in bottom of grinder (visible from bottom). placed new coupling on shaft, inserted new screw and was finished. Super fast.

Followed instructions on this website. Only difference I placed a couple blocks under the door to keep it from dropping & removed both cams at the same time. No need to remove the door from the unit.

That was soooooooooo easy. Thanks for a really wonderful website. Part was simple to find and shipped extremely fast.

I viewed the video online and removed the old filter and installed the new filter in about two minutes total time. The instructions provided in the video made the change out easy.