KECC602BBL00 KitchenAid Cooktop - Instructions

Took 2 screws under front edge of smooth top. Unscrewed ground wire from back of smooth top unit. Unplugged 2 wire bundles, from back. Took bad element out , put in new one. Put back together. About 10 min's tops. Easy peasy.

really easy! Removed 2 screws under the glass top at the front, access from the open oven door, then removed the ground wire, removed the stove top, took the element holder off,( 2 screws)and replaced with new element, 30 minutes. I ordered the part and came within 18 hrs of ordering it, fantastic experience.

Lift the cooktop out of it's inset in the counter top, flip it upside down and lay it on towels to protect the cooking surface. There is a raised rectangular panel that covers the switches located about the center front of the bottom. Remove this panel with a small nut driver to expose the switches. Now, locate the dead switch and place a strip of masking tape pointing to it and lapping around the edge so it can be seen when the unit is flipped back upright. Flip cook top back upright. Locate the correct switch by observing the masking tape. There are two small, short-threaded, phillips screws holding the switch in place. They must be accessed from the knob hole (remove rubber grommet)and at a slight angle. There is very little room to extract the screws...this is where I used the magnet to magnitize the tip of a small screw driver. Once the screw is free of the threaded hole, lift it with the magnetized screwdriver out through the knob hole. The switch will fall out easily when the two screws are removed. If you drop one of the screws inside the stove top, don't panic, I was able to shake the cook top and retrieve the screw. Now, flip the top back upside down. Using a pair of pliers remove each wire one at a time from the bad switch and connect it to the same terminal on the new switch...this way there can be no mistakes. Be sure the rubber insulator removed from the bad switch and placed on the new one. Position it where the screw holes show through, then place the switch in position. Turn the top back over in the upright position but position it where you can reach underneath it with your left hand. You will have to hold the switch and maybe move it around slightly to aline the screw holes when replacing the screws. Take a screw on the end of the magnetized screwdriver and carefully insert it into the knob hole and into the switch bracket. once you get one started, the other will be easy. I don't recall the screw replacement being any problem, just that you have to handle the screws carefully, so as to not drop one inside the cook top. Now, flip the top back over and replace the cover over the switches and replace the top in it's cabinet. The job is complete, Oh, and don't forget to flip the stove's cirduit breaker BEFORE even touching the stove!

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.

Took off top and pulled out old element and plugged in the new one

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.