Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
After using the self cleaning feature for the 10th or so time, the range locked up and nothing worked.
First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.
Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.
I first removed the door from the front of the oven according to instructions that I found on the Internet from others that have had similar problems. I then removed a total of 8 screws - 4 that were holding the door together, and 2 each for the two hinges that I replaced. After replacing the hinges, I re-installed the 4 screws and then guided the oven door back into place. It took probably about 20 minutes from start to finish, and the news hinges that I purchased solved the problem perfectly.
Upper double oven would not heat following a power failure during the clean cycle
I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new thermostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.
Lower the oven door. Insert the locking hinge pins. Pull the door away from the oven. Remove the 4 screws, 2 at the top and 2 at the bottom, to remove the front panel. Remove the 4 screws that secure each left and right spring. Remove the old springs and install the replacements by reversing the procedure. Remember to purchase 2 springs.
Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!