KEBC107KBL04 KitchenAid Wall Oven - Instructions

first you have to remove door, so open door all the way, pull back the lever on each hinge, then close door all the way, it will be able to be pulled straight out then, but be careful, its a heavy sucker. I layed a blanket out on table and layed door on blanket, start by taking out screws around the edges of door, keep these in separate container.(don't lose any). now you need to separate the door in half, this can be a lil difficult, mine had grease build up on one end that I had to be scraped . pay special attention to how the brackets go and how the door comes apart, this info will be needed later, now that door is in half, you will need to start taking the 2 other layers of glass out, please pay attention how you take apart, it has to be replaced exactly right. take pics if needed. when you get to the broken glass, take out carefully, and place glass over opening, centered well. now you have to start replacing the other layers, the replaced broken glass is kept in place by pressure, once you get the other glass layers in do not lift up door, you will need to put in the screws under the door, one of which tightens the hinge base to the door, these are the screws that tighten the replaced glass, I found this out the hard way and had to undo the whole thing again to recenter the glass, once tight, just keep going backwards replacing the other half of door. once you do this you will either say, wow that stunk, or wow that was easier than I thought. if you don't have patience, then take the door and glass to a repair shop, because you are dealing with 3 pieces of glass costing 50.00 each. be smart.

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

The Kitchenaid oven has 2 interior oven lights. They are behind rectangular glass panels, in an assembly housing The repair is pretty simple. Shut off the power at the breaker box to the oven first. First remove the small screw that holds in the assembly with a Phillips screwdriver. Put down a white piece of paper towel to catch it in case it drops. It is grey color and hard to find against the bottom of the oven. This will free up the assembly and you can move it out. There is a wire on the back so it only comes out a short distance. Next the glass panel covering the bulb must be removed. The small metal clamp with 2 projections that act like a spring to put tension on the glass. Gently pull this out parallel to to the glass and it will release the lens. The old bulb is a simple 2 prong halogen that pulls out easily. Replace it with the new bulb carefully pushing the prongs in. If you did not turn off the power the light will come on immediately. it will get hot quickly so don't touch it for more than a few seconds. Next slide the glass lens back into place into the back of the assembly. Slip the other clip with the screw back on the front. Replace the assembly back into the oven side opening. Secure by replacing the small screw removed in the beginning. You are done. It is about a 5 minute job start to finish. I would replace both bulbs even if only one went out because the other one probably will go out a short time later and you will have to go through this again soon. Oh, and cheap bulbs are not worth it. They are very dim and burn out quickly. Go with the better bulbs you get from PartSelect.

My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Ordered a replacement part and during installation tightened the top mounting screws too tight and shattered the replacement part. Ordered a new replacemnte part and installed without overtighting mounting screws. Repair went well. I caution others not to overtighten top mounting screws. These are same screws that attache the SS pull handle on oven door.

As I did not have a manual, I found all the website instructions very helpful. I had quite a hard time after installing the glass to figure out how to put it back together. The insulation between the oven glass is tricky to keep in tact. I also did not have allen wrenches to keep hinges open, so I used a variety of large bolts and screws. Finally after lots of hours, and almost calling a repairman, I did do it!

Hardest part was getting the oven door off. Since I bought this house with oven already in place, I had no owner's manual. Tried to get it off with tips found on this site, no go. Went online and found the manual which said to insert allen wrench in holes in hinge, then lift up FROM THE BOTTOM. That is the key. Got door off, then found that replacing the inner glass is a multi step process that starts with the outside door, then multiple brackets to the next inside glass, then more braces to next glass, then finally you are at the broken (inside) glass.My advice would be to take pictures on cell phone or whatever of each level, so you know what goes where when you put it all back. I figured it out but would be faster with a picture. Anyway, got all together and the oven works fine, door looks great!.

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

Had to screw off old terminal block & screw on new one

I removed the oven door using the instructions in the book that came with the oven useing 2 allen wrenches as described. I called up the parts list for the oven door on my computer and made a copy.This was very helpful in removeing the door and getting to the broken glass and installing the new glass The one thing that that i regret was not ordering the insulation frame that went around the new glass. It was difficult getting it back in place.I would order this part if I have to do this again. I ordered the new glass on a Saturday and the new glass was delivered on Tuesday.Thank you for the great service. Bill- Texas