KEBC107HWH3 KitchenAid Wall Oven - Instructions

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

This 60 y.o. female had no owners manual. I completely relied on the information of this forum. *Recommend having a work area prepped before starting. I used a thick beach towel on the kitchen table. A layer of newspaper to catch all the dirty bits is a good idea.*You must remove the door - I followed the instructions using the allen wrench in the holes of the hinge. Open door. I put the short end of the wrench in the hole and leaned the long end against the oven rim. Start closing door and when almost closed, lift up to remove.*Place door handle side up on work surface to remove the 4 screws that hold outermost glass in place, 2 at top and two in brackets at bottom. Lay this aside in safe place on table. *Take off each layer to reach broken glass. *The hinge assembly has to be removed and the allen wrenches have to come out in order to accomplish this. Squeeze the hinge to take pressure off wrench to remove. Gloves help protect your hands for this step.Remove 2 screws each side. Keep each hinge next to the side it came from so you reassemble correctly.*If you have a phone with photo capability - I recommend you take a photo of each disassembly step. This saved me when it came to replacing the two brackets that hold the inner two pieces of glass. Clean all parts before reassembly (this takes the longest amount of time). I placed a thick cup towel in my sink and scrubbed. The cleaner I use for my glass range surface worked best. Dry thoroughly. When you get to the shattered glass remove it very carefully to avoid damaging the insulation underneath. I wish I had just purchased replacement insulation. Once the glass is replaced, everything goes back in reverse order. Now, here's the thing. I spent alot of time scrubbing. So, by the time I got to reassembly, I was bamboozled by the two 10 inch aluminum brackets that hold the two inner pieces of glass in place. So, to avoid any confusion, pay close attention to how these two brackets are placed or take pictures. This was an easy fix that went really well thanks to all the helpful info found here.

Followed the directions from the owner's manual to the letter. It really is quite easy but much easier for a second person to help, especially removing the heavy door. The part came very quickly - within 2 days which was great! Now I don't have to use duck tape to keep the door closed and can actually use my oven!

First...record, film....something while dismantling oven door. This all started due to cleaning the interior glass. Had to hire a repairman to put door back together...I lapsed in remembering where one clamp ( outside the door) went. $200 later door is reassembled and CLEAN...but the glass moved. So called back repairman. In the process of debating with him re: the glass movement...I hit the glass piece on the corner and it shattered .. My fault...I ordered a new glass piece for at least 1/2 the cost repairman quoted and preceded to repair. I took pictures to remind me of proper placement of screws and clamps....put back together and guess what glass does not shift!! Being a woman...I am very proud of myself.. Just remember to document your steps and you will be fine.

I lifted the door from the oven. I reviewed the break down of the parts. The only tool needed was a screw driver to disassemble the door. I stacked each part in the order it was removed and replaced them in reverse order. PS, I cleaned the old glass before it was reinstalled it.

first you have to remove door, so open door all the way, pull back the lever on each hinge, then close door all the way, it will be able to be pulled straight out then, but be careful, its a heavy sucker. I layed a blanket out on table and layed door on blanket, start by taking out screws around the edges of door, keep these in separate container.(don't lose any). now you need to separate the door in half, this can be a lil difficult, mine had grease build up on one end that I had to be scraped . pay special attention to how the brackets go and how the door comes apart, this info will be needed later, now that door is in half, you will need to start taking the 2 other layers of glass out, please pay attention how you take apart, it has to be replaced exactly right. take pics if needed. when you get to the broken glass, take out carefully, and place glass over opening, centered well. now you have to start replacing the other layers, the replaced broken glass is kept in place by pressure, once you get the other glass layers in do not lift up door, you will need to put in the screws under the door, one of which tightens the hinge base to the door, these are the screws that tighten the replaced glass, I found this out the hard way and had to undo the whole thing again to recenter the glass, once tight, just keep going backwards replacing the other half of door. once you do this you will either say, wow that stunk, or wow that was easier than I thought. if you don't have patience, then take the door and glass to a repair shop, because you are dealing with 3 pieces of glass costing 50.00 each. be smart.

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

The Kitchenaid oven has 2 interior oven lights. They are behind rectangular glass panels, in an assembly housing The repair is pretty simple. Shut off the power at the breaker box to the oven first. First remove the small screw that holds in the assembly with a Phillips screwdriver. Put down a white piece of paper towel to catch it in case it drops. It is grey color and hard to find against the bottom of the oven. This will free up the assembly and you can move it out. There is a wire on the back so it only comes out a short distance. Next the glass panel covering the bulb must be removed. The small metal clamp with 2 projections that act like a spring to put tension on the glass. Gently pull this out parallel to to the glass and it will release the lens. The old bulb is a simple 2 prong halogen that pulls out easily. Replace it with the new bulb carefully pushing the prongs in. If you did not turn off the power the light will come on immediately. it will get hot quickly so don't touch it for more than a few seconds. Next slide the glass lens back into place into the back of the assembly. Slip the other clip with the screw back on the front. Replace the assembly back into the oven side opening. Secure by replacing the small screw removed in the beginning. You are done. It is about a 5 minute job start to finish. I would replace both bulbs even if only one went out because the other one probably will go out a short time later and you will have to go through this again soon. Oh, and cheap bulbs are not worth it. They are very dim and burn out quickly. Go with the better bulbs you get from PartSelect.