Parts That Fix KitchenAid Dishwasher KDTE104DSS0 Not cleaning dishes properly
Not cleaning dishes properly is a commonly reported symptom for the KDTE104DSS0 KitchenAid Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your KDTE104DSS0 KitchenAid Dishwasher that will fix Not cleaning dishes properly. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This filter works with the water pump in your dishwasher. It prevents debris from entering the pump and causing damage. As a result, the filter can occasionally become clogged or damaged, and will need to be replaced. A good indication of a damaged filter is if your dishwasher is not draining or cleaning the dishes properly. This filter has a gray plastic top and bottom that are approximately 5 inches in diameter. This is a genuine OEM part that comes directly from the manufacturer. To replace the filter, simply turn it counterclockwise to unlock, and then screw in the new filter
Measures level of soil in the water.
This is an upper spray arm for a dishwasher. While the appliance is in use, the spray arm rotates while water travels through it to distribute water evenly throughout the dishwasher tub. This ensures the dishes are efficiently and properly cleaned. It measures approximately 19 inches long and is grey in color.
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
Also know as a diverter valve. This diverter motor is for dishwashers. Diverter motor controls the flow of water to the spray arms. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
The upper spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. To check your spray arm, make sure the spray arms can move evenly and freely on their bearing rings and mounting brackets. Remove your spray arm and check to ensure they are straight and undamaged. This spray arm is made of high-quality plastic and is just over 5 inches long.
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. The installation has been rated as "easy" by customers. Before beginning any repair, you should unplug the dishwasher and wear gloves to protect your hands. Check your model number and user manual to see if this part is right for you! Your dishwasher should have a left and right upper rack adjuster, and both are the same part. These parts are sold individually, so if you are looking to replace both, you will need to order two parts.
Sold individually.
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
This drain hose is 6 and 1/2 feet.
Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay in its desired position. This part is sold individually. There are no tools needed to replace the positioner.
This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.
This part is used to drain water from your dishwasher.