Models
>
KDTE104DSS0
KDTE104DSS0 KitchenAid Dishwasher - Overview
Sections of the KDTE104DSS0
[Viewing 12 of 12]Keep searches simple, eg. "belt" or "pump".

Door Balance Link Kit
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS972325
Manufacturer #: 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$31.99



Dishwasher Upper Rack Adjuster
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11756150
Manufacturer #: WPW10546503
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto dishwasher rack and connects it to the track allowing it to slide in...
$42.36



Mounting Bracket
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11745496
Manufacturer #: WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$16.28



LOWER DISHRACK WHEEL ASSEMBLY
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11750057
Manufacturer #: WPW10195417
This gray plastic lower dishrack roller is a part for your dishwasher. It attaches to the bottom of the lower dishrack, allowing it to move in and out smoothly. If the lower dishrack stops moving in a...
$57.56



Dishwasher Positioner
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11750093
Manufacturer #: WPW10195840
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
$36.95



Dishwasher Dishrack Adjuster
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11750092
Manufacturer #: WPW10195839
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$45.62



Dishwasher Drain Pump
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11753379
Manufacturer #: WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$88.83



Dishwasher Dish Rack Slide Track - Left Side
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS12584376
Manufacturer #: W11259785
$81.39



Tine Row
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS10057161
Manufacturer #: W10728160
The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is...
$62.50



Dishwasher Dish Rack Slide Track - Right Side
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS12584377
Manufacturer #: W11259786
$69.36



Dishwasher Door Seal
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS12348515
Manufacturer #: W11177741
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
$65.23



Retainer Clip - Black
In Stock
Order within the next 10 hrs and your part ships today!
PartSelect #: PS11755736
Manufacturer #: WPW10503548
This part is used to hold the access panel in place. Sold individually.
$26.48


Questions And Answers for KDTE104DSS0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jane
December 26, 2022
Where is water flow valve located?
For model number KDTE104DSS0

Hello Jane, thank you for your question. This Water Inlet valve PS12578165 should be located behind the lower kick plate panel in either the right or left corner. We have an installation video for you to access to see if this is a repair for you. We look forward to hearing from you soon.

Was this helpful?
Thank you for voting!
Related Parts:
Peter
10 days ago
Need to order Control Strip for top? Some settings do not work
For model number KDTE104DSS0

Hello Peter, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11756092 for the Console in Black and PartSelect Number PS8768687 for the White Console. The Electronic Control Board that fits inside the console is Part #: PS11731265 and is sold separate from the Console with the Buttons. We hope this is helpful!
Was this helpful?
Thank you for voting!
Related Parts:
Common Symptoms of the KDTE104DSS0
[Viewing 11 of 11]Leaking
Fixed by
these parts
these parts



Show All
Door latch failure
Fixed by
these parts
these parts



Show All
Not draining
Fixed by
these parts
these parts



Show All
Door won’t close
Fixed by
these parts
these parts



Show All
Not cleaning dishes properly
Fixed by
these parts
these parts



Show All
Not drying dishes properly
Fixed by
these parts
these parts



Show All
Will not fill with water
Fixed by
these parts
these parts



Show All
Noisy
Fixed by
these parts
these parts



Show All
Will Not Start
Fixed by
these parts
these parts



Show All
Will not dispense detergent
Fixed by
these parts
these parts

Show All
Will not stop filling with water
Fixed by
these parts
these parts

Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Parts Used:
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
618 of 640 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Parts Used:
-
Andrew from Alexandria, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
459 of 501 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door spring link broken
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
5. Reverse (2 to 1) to reinstall the dishwasher.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
5. Reverse (2 to 1) to reinstall the dishwasher.
Parts Used:
-
Sean from Ramona, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
150 of 166 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!