Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
after a self-cleaning cycle, oven would not warm (broiler didn't work either)
I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.
I removed the oven door using the instructions in the book that came with the oven useing 2 allen wrenches as described. I called up the parts list for the oven door on my computer and made a copy.This was very helpful in removeing the door and getting to the broken glass and installing the new glass The one thing that that i regret was not ordering the insulation frame that went around the new glass. It was difficult getting it back in place.I would order this part if I have to do this again. I ordered the new glass on a Saturday and the new glass was delivered on Tuesday.Thank you for the great service. Bill- Texas
Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.
After using the self cleaning cycle, oven would not work
This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.
re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.
The replacement door has a cushion on the top and the sides secured to the tempered glass. When you tighten these brackets they can cause the entire glass panel to break. To prevent this use seven #8 flat washers per hole on the top of the door before securing the brackets. These will act as spacers but you will still will be able to achieve enough pressure to hold everything in place when you tighten them. Hope this helps, it worked for me, florida bob!!
To prevent this from happening use 7 #8 flat stainless steel washers per the 4 oven door holes that connect to the the handle as shims before securing the attachment brackets.
Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.
took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly
First thing you must do is remove door from oven, to do this there are locks on the hinges, lift them up. Next put door into an upright position with door opened about two inches, lift up and pull away from oven. Lay door on flat surface with inside of door facing up. there are two screws at to of door and two screws at bottom of door remove them place to side. next there are four more screws on each corner of the inside of door, they also need to be removed. this will cause the inside and outside of door to come apart. Hold door together and flip over, be careful. remove outside of door put to side. there is a bracket at the bottom with two screws remove, and remove bracket. There is a bracket at top with one screw remove. there are two pieces of glass be careful remove the two pieces of glass to get to the broken piece. Clean broken glass be careful not to cut yourself. Remember how you removed everything to put back together, do everything in reverse. Good luck, it's not that bad.
The inside glass on the oven door was cracked and needed to be replaced.
I took the door off the hinge, laid it on the kitchen island and began to unscrew the outside screws. Be sure to have a bowl to place all the screws so none fall to the floor. I would recommend taking pictures with a camera phone as you dismantle each piece. The extra time was spent trying to remember how to put the 4 panes of glass back together....and if I had pictures to refer to it would have been easier. SECOND TIP- DO NOT have your husband help with any of this. I probably could have finished in less than 30 minutes if I was doing it by myself. Once he went to bed, the reassembly was much easier.