Models > KCMS2055SSS0 > Instructions

KCMS2055SSS0 KitchenAid Microwave - Instructions

All Instructions for the KCMS2055SSS0
16 - 30 of 61
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Turn table would not turn
Took the cover off, had a lot of screws but easy. Removed the old motor and inserted the new motor. Replace the metal cover and it was ready to go. Can't believe I have waited so long to do this. I was going to replace the microwave but could not find the correct size to fit the cabinet.
Parts Used:
Turntable Motor
  • maxine from CLEBURNE, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door stopped opening
Unplugged appliance. Removed external cover's screw's from the microwave. Unplugged 3 internal plugs for wiring harness to the control panel which houses the door latch. Removed old door latch, carefully snapped new door latch in. Reassembled unit in reverse of dis assembly.
Parts Used:
Door Latch Bracket
  • Roger from Lucama, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat
Removed case,
Discharged HV capacitor and removed cooling fan.
Unscrewed ground end of HV diode and unplugged from HV capacitor.
Installed new diode by reversing the order. In my case, the problem was the magnetron was bad, so I replaced it as well.
Parts Used:
Black Sleeve Diode
  • John from SANTA CLARA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door opening mechanism failed suddenly
Although the housing cover of the microwave had the "tamper-proof screws" described by earlier commenters, I easily removed them with pliers rather than a special screwdriver. Like others, I found that one of the two hinge posts on the plastic Door Latch Bracket had broken off. The broken bracket could be removed easily, but I had trouble fitting the blade of the replacement part into position until I loosened one more screw on the receiving latch board to allow extra maneuvering room. Only then did both hinge posts fit into their proper mounts and snap in easily.
Parts Used:
Door Latch Bracket
  • Bob from DENVER, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave slowly stopped heating food
Initially we started looking to buy a replacement microwave to replace our 13+ year old built-in microwave. It was a real pain finding a replacement to fit the exact dimensions. So I thought I'd try to find an old KitchenAid microwave. However, I was pleasantly surprised when this site came up on my search. Their website allows me to input the problems and then it showed two possible parts that needed to be replaced. I emailed tech support and asked them which part I needed. They responded very quickly and said I needed to replace the magnetron. I watched a couple YouTube videos and then pulled my microwave apart. It was incredibly easy to pull the outer cover off. The magnetron had 5 screws that needed to be removed and one electrical plug. Took me maybe 10 min to complete the entire repair. It was one of the easiest repairs I've done and so thankful for this site They saved me a ton of money from not buying a new microwave and we now have our microwave working again. In hindsight, I wouldn't hesitate. I'd order the Part now and get it fixed.
Parts Used:
MAGNETRON
  • Theodore from SPOKANE, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door can't open
Take off the cover top and both sides then i saw door latch bracket was broken one side after that I was used screw drivers take off old one out then replace new door latch bracket it very easy
Parts Used:
Door Latch Bracket
  • Danny from PLANO, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch broken
Purchaced special security type srewdriver to gain access to interior of microwwave. Latch is press fitted in roller type receiver. No tool required to remove and replce new latch. Reassembled cover and job completed.
Parts Used:
Door Latch Bracket
  • Joe from Cape Coral, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door button would not open door
Removed the microwave unit from the kitchen built in space. 4 screws hold the perimeter cover on the four corners. Unit comes out easily after unpluging from wall.
Laid the unit on the counter and removed torx and phillips screws to remove the cover that wraps around the top and sides.
Latch bracket behind the door button had one pivot post broken. Removed the old bracket. Repositioned the new bracket by pressing it in at the plastic 'ears' on the microwave. The plastic 'ears' on the microwave unit give just slightly as the new bracket pivot posts wedge into place. Replaced the cover and put the microwave unit in the built in space.
Parts Used:
Door Latch Bracket
  • Frank from Concepcion, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave door won't open
I pulled out the unit. Opened the back by using the special torx driver (bought at Lowe's). Found out that Door latch bracket is broke. Checked the computer and was prompted to the partselect.com. I compared the broken part to their diagram. Ordered the part on a Saturday, it came in on Tuesday. Stick the part to where it belong. Presto. Microwave is working like new again.
Parts Used:
Door Latch Bracket
  • Arleen from Murrieta, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Wouldn't Open
After buying the (tamper proof star bit set) it only took about 15 min. You have to take the cover off to get at the latch. I found that removing the snap wire connectors made the installation easier. I made sure to mark each one, and not to force the new latch apart to much. It sure beat paying for a service call, saved about $100.
Parts Used:
Door Latch Bracket
  • dennis from rock falls, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not open
I removed the cover using a philips screw driver and a set op tamper proof torx head allen wrench set. I inspected the latch assembly and found the door latch part broken. It was easy to remove and the new part snapped into place. Repair was finished and microwave back in service in less than five minutes. Most folks would throw their microwave away and purchase a new one, the door mechanisms are usually easy to repair and parts are available. Be careful in there because of the potential of electrocution, that is why they put the tamper proof screws in place. Next time, try to repair your appliance before you decide to throw it away, may save you some hard earned money.
Parts Used:
Door Latch Bracket
  • Brian from Bristol, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original latch broke for no apparent reason.
Remove Oven from cabinet.Remove rear outer shell, 8 screws. Loosen two screws holding receiver end of broken component which is also a gang bar for several switches. Install new door latch by inserting extended end into gang bar and one of the two rotating pins into obvious receptacle and popping the second pin into slot provided. Refastened screws holding gang bar. Cannot go wrong, holes are manufactured into receptacle which properly aligns the component. Reinstall rear outer shell, Remount into cabinet recepticle. Very simple !
Parts Used:
Door Latch Bracket
  • John from Granite Shoals, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door last half broken. Microwave door would not open
Unplug microwave. Remove the cover(mine had six screws- including 4 special screws I was able to remove the special screws with pliers. Remove the broken latch. Then you must take out the two screws which hold plastic plate that has a bunch of wires connected to it. Otherwise you can’t install the new latch without breaking the side “axle” of the latch. Once you remove the plastic plate the new latch will snap right into place. Reinstall the plastic plate w the screws and you are good to go. Note of caution. The micro cover edges are as sharp as a knife. Use gloves!
Parts Used:
Door Latch Bracket
  • Andrew from MT PLEASANT, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave not heating
removed a dozen screws-discarded large cap-replaced diode-replaced a dozen screws(took longer to replace them than remove for some unknown reason). Microwave now works(wife happy).
Parts Used:
Black Sleeve Diode
  • Mark from GREENSBURG, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave losing heating items
Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.
Parts Used:
MAGNETRON Door Interlock Switch Kit
  • John from PEORIA, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KCMS2055SSS0
16 - 30 of 61