KCMS1555SBL2 KitchenAid Microwave - Instructions

hardest part was taking the microwave down off of the wall to gain access to the diode. Thought if was the transformer but ended up being just a blown diode. remove and replace and bench test. that part took 15 minutes . moral of the story don't boil water under the side of the microwave that holds the electric components.

Followed the instructions that others with a similar problem had written about. Their experience was very helpful. My experience with Part Select was the best! Part recived in less than 24 hours. Happy household, wife thinks I'm worth keeping!

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Just took the plate out the packaging & rinsed,dried and put in the oven. I was so happy I found it @partselect online& it came in the next day or two. Will definitely use them again. It was a fraction of the cost from local parts store.

Placed in micro Great sevice. Thanks

Removed the four face plate screws and set it aside. Then I removed the three screws holding the base plate to the wall mounting. Removed the wall plug and lifted the microwave out. I then removed all the screws holding the cover on the microwave and pulled the case to the rear This left the door latch accessible. Since the old latch had broken and fallen off, I just had to figure how the new one was to be installed This was very simple to figure out and it took me about five seconds to put the new one in.. Be careful when installing because all the parts are plastic and susceptible to breakage. I then reinstalled the microwave cover and after plugging it in ,pushed it into the wall cavity and put all the screws in to hold the oven in place. I next installed the face plate and every thing was in working order, A very simple project.

Well, first of all I luckily picked your website after it had broken that day, got all the info, ordered that day, and got it the NEXT day and my husband fixed it that day. VOILA!! That may never happen again, but that was the easiest thing we have ever done. You can better bet we will be ordering from this website again,as well as letting others know about it. Very impressed, and yes, this is real.

Information provided on the web site by Part Select, were helpful and encouraging to select and buy the part needed to repair the appliance. No doubt, a skilled person having background in the repair of appliances should attend such repair job.

Great!! I set the new tray into the microwave and was done! This site has the best service I have ever seen! I'll be back when something else breaks, it is just a matter of time.

This plastic door latch bracket controls the door opening. Ours broke after 7 years of use. Probably just the plastic fracturing after years of use. Hardest part is finding the special driver to unscrew the housing around the microwave so that you can get to the control panel. Ask for something that looks like an allen wrench with a hole in the middle. I took a picture of the screw in the microwave and brought it to a big box store and asked for the correct driver. I have a feeling that a "real" hardware store (like Ace or TrueValue) may have been able to just direct me to the correct screw driver but I'm cheap so I though a big box store would be less expensive for a tool that I may never use again. Once you get the correct screw driver, opening the microwave is pretty easy. MAKE SURE THE MICROWAVE IS UNPLUGGED BEFORE YOU GO ANY FURTHER. There are a number of these "special" screws (4 to 6) and some regular screws to remove. Once you pull the housing off the microwave look at the release latch inside (behind the release press plate). You should be able to jiggle it out especially since it is probably broken on one side. Be sure to find and remove all the broken pieces. Mine had just the main latch and a small piece that broke off. Pull it out and you are ready to put the new one in. It is a little difficult putting the new latch bracket in. Try inserting one side into the holder hole and very gently pressing the other side in. Be patient; with a little pressure it will snap in. Then you simply put the housing back on, put the screws in and every thing should work. $20 bucks for the part and a half hour of work (after you find that special screw driver) is much better than buying a new microwave. Good luck!

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).

I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.

OMG! I wish everything in life were so easy.....The cooking tray of our 15 year old microwave cracked and I swore it'd be impossible to find a replacement. That is until I discovered Partselect.com!!All I had to do was input the appliance brand and part I was looking for, and there is was. Thank you, Partselect.com!!

The tip on the end of the latch broke off, so I had to carefully pry it back in without breaking the new piece. Took a few tries, but got it.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott