Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door handle broke off at bottom.
Took the microwave door off. Then read other repair stories here online and discovered that wasn't neccesary. So when the handle arrived I only had to unscrew the top visible screw, pry the bottom plastic strip off the door to reveal and remove the hidden screw. From there it was only a matter of seconds to attach the new handle and snap the plastic strip back in place. Only thing I need to mention is we did not realize the part would be coming from Canada and were surprised to see the additional postage fee charged to our debit card. Felt that should have been added up front. Not a problem, just a surprise.
I had to figure out how to get one of the screws out because I could only see the head for one of them. I removed a strip of plastic that goes around the inside parameter of the door. With that removed I foud the other screw head. I removed the remaining screw and there you have it. Put it back together and your done. . The strip around the door just snapped on so that was easy. The big problem: I received the wrong door handle from PartSelect but they had the new handle at my door the very next day. I don't know haw they did that. From Kentucky to cocoa Florida in less than 24 hours. I may have ordered the wrong part but still my Microwave was broken for four days total. I know this sounds like an ad but I'm just happy with the service. Thanks PartSelect.
First I opened the door of the microwave oven and unscrewed the top screw holding the handle to the door. Then I removed the dor gasket which obscured the bottom screw. Then I unscrewed the bottom screw and removed the broken handle. Unfortuantely, this is the second time I have had to replace a broken handle. The handle is quite simply not strong enough to endure normal usage over time. If you pull the handle in a hurry and in an awkward way it will break. Shame on you, GE. Anyway, installation of the new handle was the reverse of the removal of the broken one. Very simple. I saved myself an expensive service call and the delay in getting it replaced, PartSelect got the part I ordered to me in 24 hours! Thank you very much!
I removed one phillips screw on the inside of door. Took a butter knief and popped the strip on the inside of door to expose the 2nd screw. Attached the new handle using the two original screws. Less than 5 min. Piece of cake.
Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!
Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!
Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.
The repair was relatively ease. I have to tell you that what helped me the most was reading the experiences others had had. The repair took me qabout 7 minutes. Simply take a puddy knife and carefully take out the ring around the glass on the indide of the door. Once removed you will see the botoom screw. The upper screw is very visible. Remove the two screws and replace....its that ease.
There was one screw on top that was easily accessable, but the lower one is hidden. I first removed the door seal that goes around the outside of the door but, that didn't expose the screw. On the inside of the door there is a seal just for the glass window. I used a butter knife to open just a section of it and it immediately exposed the screw that I needed to remove.
Followed the online videos to enter the cavity to the switch holder. Noticed right away the dreaded capacitor was in back right corner behind where the touch pad had been removed. I isolated the capacitor with an old computer mouse pad for extra safety. Took some manipulations to get the switch mount out from behind the wire bundles. Once out front, easy to use small flat blade screwdriver to release each switch and replace with matching new switch. Only one switch was bad but replaced all three. Back together and working great.
Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube