JVM130KC02 General Electric Microwave - Instructions

took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.

remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.

Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple

changed the bulb

With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

so easy, but how do i turn light off?

Part recieved next day. thanks so much

My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

removed the lens cover with one screw and replaced bulb

It took a little while to figure out how to get to the screws to remove the old broken handle. Once I was able to pull off the trim from inside the door, exposing and taking out the old screws was very easy. Putting the new screws in for the new handle would have been easier if I had smaller hands, but it all worked out.

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

used small screwdrivers to insert behind black door hickey. pried it loose, undid screwa to old handle and SAVED them to put in new handle. Relatively easy.

We separated the inside of the microwave door from the outside in order to get to the screws. This was the most difficult part of the repair. We got the directions on how to do this from the internet. We did not find the screws too long because there were spacers with the original screws. We found the top spacer put in backwards because the original screws were shorter. After putting the spacer in correctly the screws that came with new part were fine.

My son had to replace the bulbs because the screw that holds the bulb shield was so tight that I couldn't remove it. It was too difficult for me to do it myself.

Used the putty knife to pry open the inside of the door, just like another gentleman did, that I read on this web site. Used the phillips head screw driver to remove the broken pieces left on the door, and replace with the new handle. Popped the back of the door in place, and finished. Very simple. Saved about $400. Love it when a plan comes together.

Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.