Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
I called the 800 number and the lady was great to work with and helped me thru all the order process and confirmed the numbers. She also told me she would try to get the order out that day which she did and I had the part two days later. When it arrived I went to the web site and reviewed the video and went to work and all went as the video said. Thanks for the help and if i need another part I will visit your site or call.
Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.
No ice, the cabinet was warm, but most annoying it broke every 6 mos since I got it
I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past
condenser fan would not come on, and when it did, made loud noise.
Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.
Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.
Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!
condenser fan motor making alot of noise, possibly going out.
A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!