JT5500DF5BB General Electric Wall Oven - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven was burning when cooking at same temperature we always cooked it on
there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance.
Parts Used:
-
Don from HASLET, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt Smell
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Parts Used:
-
Eugene from Hilton Head, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
8 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven would not hold an even temperature.
I used a Trox bit to remove one screw, replaced the oven sensor and reinstalled the screw. The whole project took less than 5 minutes.
Parts Used:
-
Jack from Bremerton, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven door window
They part we received was not the right part. Called GE and ordered a new part with the same number and it worked perfectly!! Yr part was the wrong size so has to send back. Very frustrating!!!!
Parts Used:
-
Lona from THIEF RVR FLS, MN
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan motor not operating
Removed screws from front of oven, placed a table under oven 2” below, places two rollers on table and pulled out the oven. Removed screws, replaced fan and reassembled. Move into place and secured front. Cleared faults and worked perfectly.
Parts Used:
-
John from HAVERTOWN, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Went well.
Changed the Temperature Sensor as you suggested, but the problem of 40 minutes to reach a temperature of 375 degrees F. remained the same.
Parts Used:
-
Salih Hindas / from SPRNGFLD GDNS, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt out lamp bulb
Remove oven light lens cover, remove the bulb and replace it with a new one.
Parts Used:
-
Carl from MENIFEE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!