JMW9530BAB Jenn-Air Microwave Oven Combo - Instructions

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

I watched your video and read how easy the repair was to do from other buyers. I called sears and they wanted $125.00 just for the service call and automatic 1 hour labor and did not include parts and a 8 day wait for the service call.I called your number and explained my problem and was told what to order. The element was ordered on Easter Sunday and arrived on Tuesday. It took 5 minutes to install. Thank you

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.