Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Over a period of a few months, the digital diplay gradually faded out until no longer visible
Searching the internet, I found the part I needed for the lowest price at PartSelect.com. I reviewed the exploded parts diagram for my oven at PartSelect.com to get a general overview of how the oven was assembled - then I read the customer stories to get some hints from those who had done this repair before. My oven is a combination wall oven with a microwave on top. First, I shut off the power to the oven at the breaker box and then removed the thin, long rails from each side of the oven using a philips screwdriver to remove the 4 screws. This then allowed me to remove the plastic faceplate from around the microwave. Opening the oven door, I found 4 philips pan head screws underneath the control panel and removed them. The control panel will then easily lift up and then out. There are 3 areas where you must disconnect electrical connections on the control module - pay a bit of attention here, but they are sized differently and are not hard to match back up appropriately when you reconnect them to the new module. These connection plugs pull straight out with no tool needed. The old control module is held in place with 4 hex-head screws I removed with a nutdriver. After you remove the old module, it is a good time to clean the inside of the clear diplay area of the front panel with a paper towel dampened with a bit of window cleaner. Allow this to dry and then install your new control module reversing the procdures you used to remove it and reverse the procedures to reinstall the control panel, the microwave faceplate and the side rails. Cut the power back on and sit back as your wife finally thinks you are the genius that you truly are........
Screws removed from below panel. The most difficult procedure was removing the panel from the oven unit to get to the part. After lifting up and out, the panel back was revealed. Disconnected old part by pulling the three connections and replacing with new part.
Turned off power at beaker box. Opened oven door. Removed four screws from botton of display panel. Lifted display panel up and out to remove. Unplugged three wire bundles from back of circuit board. Removed four screws holding circuit board and replaced circuit board. Reassembled panel. Turned power back on. Presto.....saved $200.00 from repair estimate.
ovens wouldn't maintain temperature after preheat cycle
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
F5 error code indicated replacement of upper oven relay board
carefully. there are many connectors to the board, and while they are pretty much color coded, and I had the wiring schematic, I had to put the new board next to the old, and remove and install each connector one by one. If I had removed all connectors and installed the new board, I would never have been able to reinstall the connections correctly.
same as all the others. Display went dim over the last two months.
Same as the others to get to the bad clock. My old part was a circuit board which was made with white material and manufactured by RoberShaw. The new one was on a green material and by another manufacture. The new one felt a little heavier and look like there were more componets on it. However the plug-in connections and the mounting method was exactly the same. Before reassembly, I used a long handled brush to clean out most of the baking gunk that had accumulated in this area and I used a clean wipeing cloth to clean the inside glass for the display. The best thing about this was the part came on the Thursday before Hollowee, I installed it as soon as I got home from work. My wife started baking cookies and cup cakes for trick or treat and all is well.
First I removed the two retaining screws that hold the element in place. I then pulled the element out about 3 inches to disconnected the two wire leads. Removed element.
Note: Retain the two screws, the new element doesn't come with new screws.
To install new element simply reverse what you did to remove old element.
1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel. 2. Reach behind panel and unplug wire connector from old switch. 3. With panel free, squeeze ears on old switch and push through opening to remove. 4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart. 5. Hold the panel up to opening to connect the wire harness to the switch. 6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.) Done!
No readout on time/temperature panel and door wouldn't stay closed.
Replacing the electronic Clock Assembly was a piece of cake - just as earlier DIYers had experienced.
The door hinges were not any harder to replace, but it does not affect the behavior of the door. The light stays on unless we keep the door closed with a hook and anchor ( bent piece of metal and a wooden wedge). Not pretty, but effective. Obviously a design flaw... keeping door closed in this way forces all airflow to top and has melted the paint into a wrinkled surface. We had a service person replace the gasket seal and hinges before, but the problem still persists. I did discover that soaking the light cover in a cola drink overnight did a splendid job of cleaning off the gunk.
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine. Mike
I removed the four screws holding the control panel to the oven. I then lifted off the panel and rested it on the the oven rack which I set in the top position and pulled out about a foot. Next, I removed the three plug in cables and removed the two screws from the frame that was holding the clock assembly in place. I put in the new part and reversed the procedure. Total time to replace part was six minutes.
My son removed the switch panel and unpluged the switch. Then he replaced it with the new switch fasten back the panel and turned the power back on and everythiing worked fine.
Oven erratic, not heating correctly, timer beeper sounding
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.