JMW8530DAS Jenn-Air Microwave Oven Combo - Instructions

There were two hard parts for me to work through.

The first was breaking off the two screws that need a special head screwdriver to remove. None of my special special head screwdrivers worked (I have a few), so I used a hammer to force them off.

The second hardest part for me was finding the correct replacement bulb on-line. My Amana Microwave is a combo Microwave/Convection type, and it's a strange little bulb - almost tube like.

Once I did find the right bulb on this PartSelect.com website it was a breeze. The part was delivered in just a couple of days (even during this Covid-19 pandemic). Once I had the replacement bulb in hand it barely took 5 minutes to install.

Thanks PartSelect!!

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

Door fell off so removal of door was easy. Removed screws holding the door together to expose hinges. Removed old hinges that were 3 screws for each hinge. Placed new hinges and installed screws then put door halves back together installed screws and then finally replaced door onto the stove. Mission accomplished

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

ordered a new tray

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

1. Order correct light bulb for unit and have it with you before removing old lightbulb.
My Microwave is built into cabinet.
2. Disconnect power (Either turn breaker off or unplug unit from wall)
3. Remove face cover on cabinet. (4 Phillips head screws)
I was able to reach in the opening in the cabinet and unplug from the wall.
4. Remove Phillip head screws holding microwave in cabinet.
5. Remove microwave from cabinet.
6. Remove Phillip head screws and torx screws holding outside cover on the back of unit and the side (1 on right side) and then remove cover.
Light bulb is on the top front right side.
7. Remove 1 philip head screw holding light bulb and unplug quick connector wires.
8. Plug quick connector into new light bulb same way it came out and place new light bulb in place and put the 1 philips head screw holding it back in place.
9. Put cover back on and all the screws. Temporary plug the unit in to test light bulb works before securing it back into cabinet.
10. Reverse order 5,4,Plug unit in wall before putting the face back on.
Done.

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

I took the broiler pan out of the shipping container and put it in the oven.

Required that i remove the built in frame and mounting. Required tamper proof socket to remove housing. I removed the old bulb and simply replaced and reverse installed the cabinet.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

First I removed the oven door - with door fully open pull the clips on the hinges all the way out, then close door as far as it will go and lift the door up and off the oven.

Then I removed the three screws on each side, that hold the oven to the wooden cabinet. I then slid the oven unit out from the cabinet about 6 inches, to gain access to the hinge receptacles.

I then removed the 2 screws that secure the receptables to the oven body, and replaced the receptacles.

Reverse steps to put it back together.

Works like a charm.

Pulled the double wall oven out about five inches and install replacement brackets on both sides. Reinstalled oven doors and slide ovens back. Piece of cake— the lower oven door closes better than when oven was installed 13 years ago. Believe I had a bracket problem from day one!

Replace the racks. No special instructions.

Removed the original rack. Checked dimensions, installed the new rack.