JMV8208AAQ - Instructions

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

Did have a difficult time getting the old bulb out as it broke off in the socket. We disconnected the microwave to retrieve the broken bulb with a needle nose tweezer and then installed the new bulb in seconds. The plate glass cover was then placed back. Ended up vacuuming the ceramic stovetop due to broken chips of old bulb when being retrieved. Thanks for the prompt arrival of the new bulb. Hope it will last as long as the other bulb of 5 yrs.

hardest part was taking the microwave down off of the wall to gain access to the diode. Thought if was the transformer but ended up being just a blown diode. remove and replace and bench test. that part took 15 minutes . moral of the story don't boil water under the side of the microwave that holds the electric components.

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Install new rotating plate

Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.

I have tried MANY times to get the proper bulb from various hardware stores with varying degrees of success. My bulb seems to burn out often because we happen to have frequent power surges. This past time I was unable to get a bulb at the hardware store which would work at all. The bulb purchased specifically for this appliance, while very expensive INSTALLS PERFECTLY WITH EASE! Well worth the extra money.

Unplugged microwave, unscrewed cover, opened bulb package, without touching bulb and pushed into holder. Plugged in microwave and alas light worked. Screwed lid back in place.

Information provided on the web site by Part Select, were helpful and encouraging to select and buy the part needed to repair the appliance. No doubt, a skilled person having background in the repair of appliances should attend such repair job.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.