JMP31BL1BB General Electric Range - Instructions

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

Went to You Tube, found the appropriate segment. "Wa La" the problem was solved. Burner is working the way it is supposed to.

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks

First I removed the two screws that hold the element in place. I then pulled the element out disconnected the two wires. THE PROBLEM IS THAT THERE IS HARDLY ANY WIRE TO WORK WITH. Otherwise I would have been finished in ten minutes.

Replaced

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!

it was real easy, I just watched my husband do it!

The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.

Removed the old burner bowls, replacing them with the new ones.

Lined up the prongs and slid it right in, took 30 seconds.

As with all of my orders from Part Select the part was as correct and arrived in a timely manner. The installation was easy. Remove two screws, unplug the old element from the wires, install wires on new element and reinstall the element. Restored power and everything worked fine.
Thanks,
Ken Fuelleman