Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JKP90BM1BB > Instructions

JKP90BM1BB General Electric Microwave Oven Combo - Instructions

All installation instructions for JKP90BM1BB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave oven combo repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JKP90BM1BB
31-45 of 117
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Micrwave won't run - turntable turns backwards when door opened...

  • Customer: Roger from Fountain Hills, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Oven temperature would not go above 240 degrees

  • Customer: Glenn from Grapevine, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

Microwave wasn't heating up foods

  • Customer: William from LAKE ELSINORE, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

Turntable wouldn't go around

  • Customer: Brenda from SAN TAN VLY, AZ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Ordered the part and pressed it on spindle.

The Guide Roller attaches to the drive mechanism. The assembly hub had cracked an.d was unable rotate the plate inside the microwave

  • Customer: James from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Simply removed the cracked Guide Roller after finding that there was no way to repair the piece. Upon receipt of the part via FedEx it was a simple matter putting the new part in place. Things work fine.

microwave Quit working but lights worked

  • Customer: Rick from Muncie, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
llation

Microwave appeared to work. Fan worked, timer worked plate rotated. It just didn't heat the food!

  • Customer: Mark from Hanover Park, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

bulb burnt out

  • Customer: Christie from NAPERVILLE, IL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked

Microwave stays on when door opened

  • Customer: Charles from OAKDALE, NY
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

Roller guide under glass tray was broken, would not spin

  • Customer: Ladonna from Peoria, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Purchased a new roller guide, simply dropped it in to place and the problem was solved. It took longer to open the box than it took to make the repair. Quick and easy.

Oven light

  • Customer: Letty from KERRVILLE, TX
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)

Door latch would not allow you to remove food when done cooking

  • Customer: STEVAN from LEAVENWORTH, WA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Turned breaker off at panel first. Removed three sheet metal screws holding top control panel with 8mm socket, removed the two 8mm nuts holding the locking mechanism in and one 8 pin plug, replaced with new part. Put back control panel and I was enjoying homemade oatmeal cookies 30 minutes later. We were using a toaster oven for months until I found the part from this site. The GE repair guy wanted $900.00 to fix it. The part was only $165.00 from this site. Thanks folks!

Not Reaching Temperature above 300 Degrees

  • Customer: Ron from SAN TAN VLY, AZ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

broken turntable

  • Customer: PHILIP from GEORGETOWN, TX
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
replaced it with the new one.

Microwave touch buttons failing, last straw was Auto Defrost became stuck on.

  • Customer: Raymond from RENO, NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
One should be used to working with PC boards or hire repairman. Open microwave door, remove two torx screws from front panel edge. Panel left side will swing out. Right side hinges can be lifted up and left to disengage from oven. There's also a bottom plate hinge with two screws in groves. Slide plate so the screws reach a wide part of the grove and the plate will lift off. Remove the plate from the control panel. There's two flat ribbon connecters, pull up on the top edge of the connectors to release the cables. Remove the screws holding the two sets of pc boards to the panel. The panels can be hung form their wires, they don't weigh much. Remove the latch button from the panel, there's a pin/hinge on one side and some plastic fingers on the other. Examine everything to figure out how to remove the button. Carefully pry the hinge apart enough to remove the button and there's two keepers that also need to be pried apart to release the button. There should be a spring too, the new panel needs them. Reassemble in the opposite order. Hint: when reinserting the flat cables, the connecter top/latch tends to fall in, make sure it's pulled up away from the board to insert the cable easily. Once in, push down on the latches to lock the cables in place. The screws holding the boards are self tapping. The new panel won't have threads so you may want to insert the screws first to cut the threads to make it easier to reinstall the screws in mounting the boards to the panel. Otherwise the screws take a lot of torque which can result in driver slipping and board damage. Other hints, turn off power during the installation. Also, boards are static sensitive, keep touching the metal of the oven when handling the boards or use a grounding strap. Lastly, take a picture before removing screws so you put the right ones back in the right holes.
All Instructions for the JKP90BM1BB
31-45 of 117