Models > JGS905KEKC > Instructions

JGS905KEKC General Electric Range - Instructions

All Instructions for the JGS905KEKC
121 - 128 of 128
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the grate foots came off
put it in but it keeps falling out. they're made narrower than my oven grate.
Parts Used:
Grate Foot
  • Sandra from Watertown, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Parts Used:
REAR SUPPORT
  • Richard from Newark, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven lights were burning out regularly
Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.
Parts Used:
Oven Light Housing
  • Douglas from Thornton, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
broil would not come on
remove oven door of course you cut gas and power off first tried to get screws out of igniter the heads broke off had to take cover off to get screws out slide range out of cabinet take back off to unplug igniter then reassemble
Parts Used:
Oven Igniter
  • Ralph from Decatur, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Igniters on gas stove were randomly sparking.
Backed off screws that held the burner base over the gas opening. Removed C ring and spring and slid out old igniter, cleaned base, inserted new igniter and replaced burner gasket, refastened base and the job was done. Repeated for other for burners. Easy.
Parts Used:
IGNITER Burner Gasket Burner Gasket Burner Gasket Burner Gasket
  • William from New Concord, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Parts Used:
REAR SUPPORT
  • Mario from Deer Park, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken Door Switch
I unplugged the defective plug and replaced it with the new one. Took 5 min total
Parts Used:
Door Light Switch
  • Peter from Green Valley, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
rear drawer supports broke
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Parts Used:
REAR SUPPORT
  • TERRY from RICHMOND, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGS905KEKC
121 - 128 of 128
Back to Top