JGBS18DEN2WW General Electric Range - Instructions

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it.
I had the schematic picture of the door ready in case he needed it. He didn't really.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Removed old gasket and pried out clips with screwdriver. Installed new gasket.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

remove all loose components on range top (grates, caps, disbursement / diffuser heads. Take a T-15 screw driver and unscrew each of the three screws on each burner. Have a large flat headed screwdriver ready. Lift up on the front lid of the range, it should life about 1/4 inch. There are two clips that hold it down, about 6 - 8 inches in from either side. Press then towards the back (away from you) one at a time, while lifting on the lid.. it should pop free. WARNING: if you did not remove the torx screws first, be careful are you will now bend the gas lines running to the burner. Once loose, remove the old clip from the igniter, so that it lifts free. unplug the igniter from the electrical cable (pulls out from bottom). attach new clip to new igniter and re-attach electrical line to new igniter. close lid and re-attach all torx screws. Reassemble range top and you are complete.

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Replaced old with new.

Order parts and installed - no tools needed - completed repairs less than 1 minute

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!