Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
electric storm fried oven display
I ordered a new display from the internet. I removed the panel where the display is housed, unscrewed the entire display assembly and unplugged all wires connecting it. (I made a drawing and noted colors of wires) I removed adhesive face of display and replaced it on the new display. I then screwed in the display and reconnected the wires as per my notes. I reassembled the panel and applied power and it worked like new.
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
It all began one find night baking and suddenly the oven would not light up. And so for the next few years all I ever used the stove for was for stove top cooking, See Im a single guy so its not in my nature to get to fancy when it comes to cooking home meals,but after a while the mood changes and you finally get up the motivation to fix whats wrong. The change over went easy,easier than I expected.And the part worked just fine. As far as ease of the order and receipt,couldnt have been better,I got the part within 48hrs and that is fast! Thanks to all. T.Melillo
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
First I removed the back panel and then removed the four screws that hold the display board in place.I then disconnected the wires. I installed the new board and connected the wires. I put the back panel on. I installed a serge protector and pluged in the range. Job completed and it worked.
First I tested oven sensor which checked o k. I then made a diagram of the electrical wireing to the oven control. I disconnected wireing and removed the control then with sharp knife I removed touch control pad. I placed th touch pad on the new panel and installed panel and connected wiring. Pluged into wall rec and test oven which checked o k .
Change bad/broken igniter on gas stove top burners
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.