Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Only one burner sparking on range.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel 2) Slide out Range from wall 3) Unplug Range 4) Remove back panel and unplug electrical connections to socket 5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb 6) Remove old socket from mounting flange and discard. 7) Place new socket into mounting flange 8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back. 9) Screw in new light bulb from front 10) Replace existing glass cover over new light bulb and snap wire holder in place 11) Replace back panel 11) Plug in range 12) Slide range back to original position 13) Turn on power Works like a charm! Thanks for having the parts after 30 years!
Replaced igniter pins but no joy, needed igniter module
Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.
Alarm would sound whenever oven turned on - with an error message code
Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!
everything worked on the stove except for the oven
Since I'm not very mechanical I had my service manager from work come to my house and fiqure out the problem. By using an electrical meter he found that there was no continuity in the igniter. So being the mechanical guy I am I watched him take out 2 screws that secured the the piece of metal that covers the bottom part of the stove. He pulled that part out and from there it was 2 screws to release it from the back of the stove and 2 more to disconnect the igniter from the burner tube. We ordered the part and it arrived in 3 days. I opened the box and to my dismay it was broke. I called to tell them that it was broke and they ordered me a new one right then. I had that part the next day very grateful for that. I was able then to put it back together myself and it worked. Wife is extremely happy with me.
Removed oven door, warming drawer, oven bottom, oven burner, disconnected wires to igniter. Also, instructions said to turn off gas supply at pressure regulator, {little red lever.} I also turned off main gas supply, and un-plugged power cord. Removing the igniter and replacing with new one was easy. Splicing wires and putting everything back together was also pretty easy. The only problem was when I tryed to open the gas to the pressure regulator, the little red lever popped off. Very cramped area to work in, could'nt get a tool to fit in there. So, I got some nylon string, made a loop, looped it on the notch on the pin, pulled it out and got the little red lever back onto the pin and then was able to open the valve. There is no gas going to the burner if that lever is not on holding the pin out, and you can't put that lever back on unless the pin is pulled out. If I ever do that job again I will not touch the red lever, I will just shut off the main gas supply. It would have been a pretty easy fix if that lever would not have popped off.
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
18 year old gas range, just replaced oven igniter, and tried repairing burner igniter
I replaced the oven igniter, discovered the floor of the oven had rusted through, so I replaced that as well. The burner on top of the stove would not light as it was designed, and because the 12 screws that hold the range top and burners in place were rusted in place I ended up buying a new range because removing the screws on the burners proved impossible, even when I tried to drill them out with a lefthanded screw removal tool. I should have just kept lighting the burner that would not light, with a match. That was a repair too far, that forced me to buy a new GE Range and throw this one in the trash. The igniter, oven floor replacement was easy. The burner igniter after 18 years proved impossible. .I installed the 18 yr. old burner grates on the new range, but the drip pans would not fit the new stove. New GE Range instructions were near useless. Do Not trust them, especially the Orifice change details NG to LPG.
the instructions given for this part were not 100 % accurate, our oven door required multiple, dis assembly and was unable to complete the task, local handy men refused to come to assist since the job was already started, it appears I will now need to buy a new oven , I was disapointed in the help because had we known we had the more diffcilult oven, would not have attempted, I did give the correct model and serial number to the person when discussing this part
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
