Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The burner assembly seemed to be rusting some and had become not easy to clean. The grates had just become dirty and unable to clean so they were changed out for ascethetic reasons only.
I ordered the parts on line and they came very quickly through the mail. The burner assembly came with instructions for the installation of a nut. Everything was great - from the order to the delivery to the installation.
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel 2) Slide out Range from wall 3) Unplug Range 4) Remove back panel and unplug electrical connections to socket 5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb 6) Remove old socket from mounting flange and discard. 7) Place new socket into mounting flange 8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back. 9) Screw in new light bulb from front 10) Replace existing glass cover over new light bulb and snap wire holder in place 11) Replace back panel 11) Plug in range 12) Slide range back to original position 13) Turn on power Works like a charm! Thanks for having the parts after 30 years!
I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)
I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.
Remove the cover over the spark module. Remove the two screws holding the module. Unplug the wires from the old module and plug them into the new module. Install the new module with the two screws. Replace the cover.
The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!
First just unscrew each natural gas jet and install the propane jets. if they are hard to come off just turn your wrench back and forth first until the jet turns with your fingers. Then open the oven and take out the racks. In the bottom back of the inside of the oven there is a screw on each side. Unscrew both screws lift the bototom plate of the oven and slide it back about 1/2 inch then lift out of the oven. Move the 1 screw covering the heat shield from the oven jet. Then light the top burners and turn them off just to get the gas flowing. Also light the pilot in the oven, then light the oven. To convert the oven from natural gas to propane all you have to do is adjust the jet while the oven is lit. turn the oven jet ubtil there is a blue flame with little or no yellow tips on the flames.
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.