Models > JGB916SELS > Instructions

JGB916SELS General Electric Range - Instructions

All Instructions for the JGB916SELS
61 - 74 of 74
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no racks to oven
Easily glide in.
Parts Used:
Oven Rack
  • Johnette from Baltimore, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Parts Used:
Oven Rack
  • Anne Marie from Andover, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Threads on elbow stripped out
Part was purchased to replace damaged elbow. During the conversion to LP gas the elbow threads were stripped from over tightening the collar nut. To accomplish the replacement: 1. remove 2 sheet metal screws holding protective shroud in place. 2. disassemble the compression fitting CAUTION DO NOT OVERTIGHTEN 3. loosen elbow collar nut if necessary and remove elbow. 4. reassemble starting with the compression fitting. 5. connect the elbow to the broiler burner with the collar nut 6. tighten all the way down turning nut cw for LP conversion CAUTION DO NOT OVER TIGHTEN 7. with broiler on adjust flame and check for leaks
Parts Used:
ELBOW HI BROIL
  • Ronald from Millington, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Parts Used:
BOTTOM OVEN AND DEFLECTOR ASM
  • Ruth from Somerset, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Missing oven rack
I opened oven and pushed oven rack inside.
Parts Used:
Oven Rack
  • Damaris from Easton, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No heat from Oven Burner. Alos poping explosion noise when burner ignited
I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr
Parts Used:
Burner with Igniter
  • Bruce Lee from Carson City, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Parts Used:
BOTTOM OVEN AND DEFLECTOR ASM
  • Mary from Redondo Beach, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Oven Probe broke
Ordered new probe
Parts Used:
Meat Probe Thermistor
  • Kathleen from Munt Laurel, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Convection fan came loose from shaft
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."
Parts Used:
NUT
  • Thomas from Albuquerque, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Parts Used:
BOTTOM OVEN AND DEFLECTOR ASM
  • Joan from Watervliet, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Parts Used:
Oven Rack
  • Vicki from Irvine, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
missing meat thermistor
plug in thermistor when needed
Parts Used:
Meat Probe Thermistor
  • John R from Asheville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
orginal surface burner know where not stainless steel and starting to peel due to the heat
Replaced the burner knobs with Stainless steel knobs from Parts Select. Very satisfied with my purchase. Easily replaced by removing old knobs and replacing it with the new knobs. No tools needed.
Parts Used:
BURNER KNOB KIT
  • JoAnn from Bayville, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
I needed an oven with three racks, mine came with two.
just slipped it in
Parts Used:
Oven Rack
  • BETTY from CYPRESS, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGB916SELS
61 - 74 of 74