Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
After watching the instructional video (and flipping the breaker to my range) it was straight forward and simple. The heating element was a little bent so didn’t originally sit square/flat to the bottom of the oven so I uninstalled, bent it gently a little and reinstalled and it set down flat. It still didn’t take 15 minutes.
Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.
Turned oven circuit breaker off. Removed oven racks. Removed 2 screws from old element. Pulled element out slightly disconnected wires on each end and reattached to new element. Pushed back in and reinstalled the 2 screws, reinstalled oven racks and turned circuit breaker back on. All done in about 20 minutes.
Bought bottom element as suggested. Instruction video seemed straight forward. Not exactly.When I unscrewed the element and gently pulled it out to access the connector, one came out an inch or two, however the left side would not slide out. Tugged a little and it released the connector which jumped back inside the oven. Had to slide the oven out from counter, remove a rear covering plate (2 screws and no problem) and found the new element connectors protruded through the rear of the stove for connection. They were covered by the large rear plate I had removed. Screwed the plate back on and, slid the stove back into position, restored power and all was good. Stove heats properly. Happy.
The burner would turn on and not off. The temperature just kept accelerating.
Raised the unit and blocked it with 2 boards. TURN OFF THE POWER IF YOU WANT TO COMPLETE THIS REPAIR. Removed the philip head screws for removal of glass top. Remove the corner screws on switch end. Remove screws holding the switch. Remove screws holing the bracket for all switches. Lift and roll gently to get at wiring. Follow the directions for moving wires from old switch to new switch. MOVING WIRES IS THE MOST IMPORTANT STEP. Reverse your procedure to put back together and when finished remember to turn on the power.
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
I did not mark wires with their associated numbered connections on the old burner but I did take pictures prior to removing the old burner. This slightly complicated finding the right connections for the wires on the new burner but the photos taken were invaluable in doing so. The placement of burner connections between new and old was different. Additionally, there were 2 connections on new and old that were not numbered. These turned out to be the power to the inner and outer coils and their connections were determined by examining the burners and connecting accordingly. Also, not mentioned in the instructions was a light on the new burner that the old burner did not have. I removed the light and the wire connecting it to the burner and connected the freed new burner connector based on the old/new burner connection numbering. Despite my lack of confidence that I correctly installed the burner, it worked on the first try and I am very happy to have it fully functional again.
The replacement unit was a substitute part. Wiring slightly different. Instructions bare minimum. Follow instructions and it does work. No instructions as to how to remove the stove top. Been there before so sort of knew how. Nothing in the Jenn Air manual for stove top removal. The control panel has to be removed, two screws on each side and four hex screws on bottom, this allows for the disconnect of wiring for the top. Remove the two trim pieces one on each side. One screw at top and one at bottom. The trim piece will move towards the rear and come off. Two screws on each side and two in the back will release the top. Remove top and lay on padded surface. You are ready to replace unit.
My genius scientist husband responsible all electric string connections, I responsible buy right parts and all support work, we worked as a team and fix the problems:) :)
replaced burner by following the wiring from the photo we took. worked god except was cooking to hot and would not cycle. went to use my smaller burner in the back on the same side and the center of the double came on. so we watched another video looked at what we did wrong with the wiring. here we wired the burner slightly wrong we did not follow the numbering. this time followed the numbering and all is good. burner is working good and cycling.
Engaging dual burner switch would blow breaker. All other elements worked fine.
Isolated circuit by disconnecting cooktop breaker. Disconnected blower duct, raised cooktop above the countertop to access screws holding the glass surface. Blocked in place--no need to completely remove cooktop. Removed screws around top of pan with 1/4-inch nut driver--only need to remove any screws close to top of pan and glass surface. Lifted off glass surface. Dual burner switch bracket needs to be removed to access switch and to disconnect wire harness connections. Note there was one screw holding bottom of bracket which was hidden by the wire harness. I was concerned with connections from other reviews; however, in my case, the switch and connections were identical to the original--no problem. Reinstalled bracket and glass cooktop--need to remember flange location (inside versus outside) to assure easy alignment of screws. Drop cooktop back into countertop and reconnect blower duct. Powered back up and dual burner now fully functional.
• Removed the oven door (pulled right off old hinges) • Removed two screws • Removed broken hinge • Placed new hinge in place • Replaced screws • Replaced oven door.