JES9800AAW Jenn-Air Range - Instructions

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

Replaced it

Moved the stove, unplugged it. took the back off, took out old board installed the new one. It was just that easy and saved us from buying a new stove.

When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.
PS Be sure and remove the range door or have very long arms.

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Removed element's two mounting screws and disconnected the wire leads on each end. Connected wire leads to the new element and replaced mounting screws. Only took a few minutes to make the change. The oven is good as new.

Disconnected power to the range, Took off the oven door removed two screws and disconnected the two electrical connections to the heating element. Made the two connections to the new element and replace the two holding screws. Replace the oven door and plugged in the power cord. Turned on the oven to test and was finished.

This was very easy. All I did was unscrew the brackets from the back of the oven holding the element. Then I removed the wires from the bad element and reversed the procedure adding the new element. It was easy to order the right part and I got the item in plenty of time for the Thanksgiving holiday!

I had an electrician do it. The instructions were horrible. He followed the instructions from your web site. The cooktop was not on an island so he could not remove all the screws to release the top so he worked with the top propped up. When he finally got the connections on, the small burner would not work only the large outer burner is working. He went on the computer to see if he could get more information but was unable to find any information.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

Plugs in easily, screws to secure